1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
ok to strip?
TimC
☆
****
Posts: 262
Threads: 27
Joined: Jan 2010
City: Rochester, NY
#1

10-27-2014, 04:53 PM
Dumb question, but I'll ask anyhow

I have what I think is a 52 cathedral.
Some jackass thought the cabinet needed improvement..
Want to see if these were photophinish at all.
Too early a radio for photophinish I think.

Tim
(This post was last modified: 10-27-2014, 04:57 PM by TimC.)
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

10-27-2014, 05:10 PM
Nope, no photofinish on a 51B...
--
Ron Ramirez
Ferdinand IN
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#3

10-27-2014, 06:14 PM
Great news from Ron. That radio can be saved with a lot of stripping and refinish. Nice looking little cathedral.
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
Arran
Phorum Expert
*****
Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#4

10-27-2014, 09:38 PM
 One more thing though, use proper paint and varnish remover to strip the cabinet, lacquer thinner and acetone are not going to cut it this time. However the lacquer thinner and acetone are good from removing residue after you get the paint off. It looks like someone in the 1950s or 60s had a go at "Antiqueing" this poor model 52, that was the decorating trend of doubtful taste from that time, tackiness didn't begin in the 1970s you know.
Regards
Arran
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration