Posts: 403
Threads: 40
Joined: Feb 2011
City: McPherson, KS
Just opened up a fairly nice bakelite 53-566 tonight. It has BC and what looks like the old police band on it. Lots of loud buzz/hum so caps need replacing. It has a 4-section filter cap: 40, 40, 40, 25. I'm trying to decide whether to replace the 40s with 33 or 47 mfd. Which do you think would be better? Of course a 22 will take care of the 25.
Planning to re-stuff the original container just because of space.
Thanks for your ideas.
Posts: 403
Threads: 40
Joined: Feb 2011
City: McPherson, KS
Ooops. Got this in the wrong folder. Move it if you want to Ron.
Art
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
I think either value will work fine.
Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
I would use the 47 uf if you have them laying around, or a combo of those and the 33 uf, and stuff them inside the old filter cap tube just for neatness. Interesting how the set has a cathode capacitor on the power output tube, the last few late 40s early 50s Philcos I worked on didn't have one, they had the resistor but not that small electrolytic included.
Regards
Arran
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
Using a cathode bypass cap on the output tube was an engineering design decision, not necessarily dependent on the cost of the extra part.
Including the cap increases the voltage gain of the output stage at the expense of added distortion. Eliminating the cap has the effect of providing negative feedback, thereby reducing distortion. In this case, the loss of gain must be made up elsewhere in the audio section, otherwise the radio will not play as loud as it otherwise would.
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
It is also frequency-dependent increasing gain on higher frequencies.
Posts: 403
Threads: 40
Joined: Feb 2011
City: McPherson, KS
I have lots of 47s Aaran.
Posts: 122
Threads: 37
Joined: Jul 2012
City: Coral Springs, FL
I was under the impression that you can always go a bit higher in the capacitance value (i.e - replace a 40uf cap with a 47 uf cap), but NEVER should you go lower? Is that wrong?
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Why not use 40s? I always keep plenty on hand. I like to replace all caps with the same value when possible.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
On a lower end set like five tuber in the Transitone series i think that leaving the cathode capacitor out may have been a cost saving measure given the market, it's also possible that when this 53-566 was built Philco got a deal on four section caps with the cathode cap included. I have noticed that adding one tends to improve the bass response, sometimes it increases the gain substantially, sometimes not as much, I haven't noticed any more distortion though. I have found that it's more beneficial when the set has a larger diameter speaker, like a 5'' inch or larger, otherwise it gets a little too boomy.
Regards
Arran
P.S Art, if you have lots of 47 uf caps, use them, the pi filtered power supplies in these AC/DC sets are so crude they can use all the filtering they can get, especially on the output filter cap.
Posts: 403
Threads: 40
Joined: Feb 2011
City: McPherson, KS
Does anybody have a clear copy of the schematic (Riders Philco page 23-45) and chassis layout (page 23-44) scans they can email to me? Nostalgia Air stuff is a little fuzzy on my end. Email is artdrhs at yahoo dot com
Thank you.
Art
Posts: 1,155
Threads: 23
Joined: Jan 2014
City: Wellborn Florida
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Cannot Adjust an IF Transformer’s cores
|
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM |
Cannot Adjust an IF Transformer’s cores
|
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM |
PT-6 antenna connections
|
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM |
Cannot Adjust an IF Transformer’s cores
|
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM |
PT-6 antenna connections
|
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4.
Yes, pin 6 of the 7C6 is...RodB — 07:34 PM |
bridkarl
|
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM |
Cannot Adjust an IF Transformer’s cores
|
Joseph, now you are an engineer!!RodB — 06:37 PM |
PT-6 antenna connections
|
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM |
Cannot Adjust an IF Transformer’s cores
|
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM |
PT-6 antenna connections
|
I seem to have lost my way on this PT-6.
I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM |
Who's Online
|
There are currently no members online. |
|
![>](https://philcoradio.com/phorum/images/bootbb/asb/right_arrow.png)
|