Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Atwater Kent 206
#1

Just need an opinion- to strip or leave it be. Stripping is not that difficult thing to do, just wonder if it still looks presentable.
Some like it that way, "patina" and all, not sure. Thanks.

[Image: http://i881.photobucket.com/albums/ac17/...172154.jpg]
#2

My opinion:

[Video: http://www.youtube.com/watch?v=Ho02oKHuveY]

--
Ron Ramirez
Ferdinand IN
#3

Only 1 picture, but, from that, I would 'let it be" too.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#4

I would also leave it as is. The finish is original only once, and for 80 years old it looks very nice. 
#5

I agree with everyone else..... leave it alone. The most I would do is a Go-Jo cleaning, some Howard's or Old English, and some quality paste wax.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

It's a good looking cabinet. Paul said it best Icon_smile
#7

We have consensus by mavens..Needless to say, will comply.
Thanks guys.
#8

  I would have to see more pictures, with sharp focus, brighter lighting, and not at odd angles, sometimes they make things look better then they really are in person. A case in point was the Rogers Ten-60 I got from a guy selling it over craigslist, in a front on view it looked pretty nice, when I went to look at it in person I realized that someone had rubbed it down with Howard or some other scratch hiding product. Now obviously this set is not being pedaled on craigslist but a rub down with Gojo can have much the same effect, until the remnants of the Gojo evaporates.
Regards
Arran
#9

I wouldn't strip that. You can always touch the small worn areas up. If you use Howards you can touch up or go over it at any time with Laquer based products.
#10

(11-03-2014, 01:39 AM)Arran Wrote:    I would have to see more pictures, with sharp focus, brighter lighting,  remnants of the Gojo evaporates.
Regards
Arran

Your wish is my command.. Here it is, w/o GoJo:[Image: http://i881.photobucket.com/albums/ac17/...df5fda.jpg]
[Image: http://i881.photobucket.com/albums/ac17/...6fdca8.jpg]

[Image: http://i881.photobucket.com/albums/ac17/...9b882b.jpg]
Keeping the cabinet original, I did not want to have the chassis look brand new, just clean.
[Image: http://i881.photobucket.com/albums/ac17/...875acb.jpg]
[Image: http://i881.photobucket.com/albums/ac17/...ba0ff5.jpg]




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 5558 online users. [Complete List]
» 1 Member(s) | 5557 Guest(s)
Avatar

>