Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Canada 39 or 41-722 Tropic
#46

(11-13-2014, 08:34 AM)mikethedruid Wrote:  I am not sure, and don't have the records handy to check, but one reason for the difference between US and Canadian wire type, rubber covered vs. cloth covered, could be a difference between UL and CSA requirements at the time.

I suspected as much.

But what I find really interesting is that the IF transformers have/had rubber-covered leads! So I can't help but wonder how many of the parts were actually imported from USA Philco and then assembled into radios in Canada.

The two electrolytic capacitor cans in my 39, as well as the lone bakelite block, are all stamped "Made in U.S.A."

--
Ron Ramirez
Ferdinand IN
#47

 No, the Canadian electrical code had nothing to do with the lack of rubber wire in Canadian built Philcos, Rogers as well as Canadian RCA and G.E used yards of the stuff in that era, especially Rogers which used almost nothing but rubber wire, except for external wires, it it were illegal then none of them would have used rubber wire.
Regards
Arran
#48

Ron,
  We are all at various levels of knowlege and experience. I have had an interest in old radios for 50+ years. I really enjoy making them come to life again. Also I enjoy listening to and looking at them. However I never gave a lot of thought to " restoration " and certainly never seriously considered restuffing a capacitor just for looks.
  After joining this forum and seeing what others do and how it is done I better understand some aspects of why people go to that length. So I say keep up with the resoration articles because they are enjoyable and educational.
                                     Thanks for all you do.
                                                     Henry
 
#49

Henry

Thank you! I've been messing around with vintage radios for a little over 40 years now, since I was 14 years old. You do the math. 14 + 40 = old. Icon_lol

(and don't tell anyone, but I once experimented with restuffing paper caps using melted wax, decided it was too much work, and abandoned the idea until just recently, when I started restuffing paper caps again, using hot glue instead of wax to reseal them.) Icon_wink

--
Ron Ramirez
Ferdinand IN
#50

Ro,
 Your secret is safe with me.
                      Henry




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM
American Bosch Model 802 auto radio
I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM

[-]
Who's Online
There are currently 4775 online users. [Complete List]
» 1 Member(s) | 4774 Guest(s)
Avatar

>