1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
32-8274 trans
zfrederick
Junior Member
**
Posts: 16
Threads: 4
Joined: Nov 2014
City: VA
#1

11-28-2014, 03:23 PM
I'm in need of a replacement for the 32-8274 transformer but am having issues trying to find a replacement one. Can anyone point me in the right direction for a replacement. It has leaked out everywhere
Find
sam
Phorum Expert
*****
Posts: 2,573
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#2

11-29-2014, 03:43 PM
zfrederick
welcome to the phorum
sam
Find
morzh
Odobenus rosmarus
******
Posts: 16,481
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#3

11-29-2014, 08:21 PM
Have you tried it though? It might've overheated but potentially still might work.
Try to run it UNLOADED for a few minutes, see what it consumes and whether it heats up.
Find
morzh
Odobenus rosmarus
******
Posts: 16,481
Threads: 573
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#4

11-29-2014, 10:58 PM
<P>Philco output transformer 32-8274: Primary impedance: 9000, Secondary impedance: 3.5. Power is not listed for this transformer, but similar physical sized ones are rated at 15 watts.


(from the other forum archives)

Which tells me 125 seies PP transformer (higher wattage model) will do.

125E.

Connect Voice coil to 2 and 4.

http://www.radiodaze.com/category/570.aspx
Find
Arran
Phorum Expert
*****
Posts: 4,865
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#5

11-30-2014, 01:32 AM
 You could also try Edcore, they seem to have a good selection of tube type audio output transformers:

https://www.edcorusa.com/pushpull

Regards
Arran
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration