1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
32-8274 trans
zfrederick
Junior Member
**
Posts: 16
Threads: 4
Joined: Nov 2014
City: VA
#1

11-28-2014, 03:23 PM
I'm in need of a replacement for the 32-8274 transformer but am having issues trying to find a replacement one. Can anyone point me in the right direction for a replacement. It has leaked out everywhere
Find
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#2

11-29-2014, 03:43 PM
zfrederick
welcome to the phorum
sam
Find
morzh
Odobenus rosmarus
*****
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
#3

11-29-2014, 08:21 PM
Have you tried it though? It might've overheated but potentially still might work.
Try to run it UNLOADED for a few minutes, see what it consumes and whether it heats up.
Find
morzh
Odobenus rosmarus
*****
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
#4

11-29-2014, 10:58 PM
<P>Philco output transformer 32-8274: Primary impedance: 9000, Secondary impedance: 3.5. Power is not listed for this transformer, but similar physical sized ones are rated at 15 watts.


(from the other forum archives)

Which tells me 125 seies PP transformer (higher wattage model) will do.

125E.

Connect Voice coil to 2 and 4.

http://www.radiodaze.com/category/570.aspx
(This post was last modified: 11-29-2014, 11:01 PM by morzh.)
Find
Arran
Phorum Expert
*****
Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#5

11-30-2014, 01:32 AM
 You could also try Edcore, they seem to have a good selection of tube type audio output transformers:

https://www.edcorusa.com/pushpull

Regards
Arran
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5134 online users. [Complete List]
» 1 Member(s) | 5133 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration