Posts: 79
Threads: 8
Joined: Dec 2014
City: Wood River, Il.
Hello All,
This is my first post on this site. I am working on one of my Philco model 95 receivers and have run into a problem. Has anyone had any experience in restringing the tuning cables on the tuning condenser? I am asking if there are any tricks or methods to getting the cables installed and tracking right. I have been at it for about 2 hours and am running out of ideas. The cables were off the drums when I got the set, but all the pieces are present, including the springs. I can see how it is supposed to operate, with the cables rotating on opposite spools and keeping the tuning drum in tension, I just haven't figured out a means of getting both cables installed. To be honest I am getting a little frustrated. 
I am also wanting to know if there is a safe way to clean the brass tuning dial. All the numbers and lines are intact and I would like to keep it that way. What is a good cleaning method to use here.
Thanks for any advice in both matters.
Chris h
Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Hi Chris, welcome to the Phorum! Unfortunately I can't answer your questions but since no one had responded yet I just wanted to welcome you and let you know there will likely be someone who can help.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Chris
Send Phorum member Radioroslyn (Terry) a PM or email. As I recall, he has done this work before and can advise you on how to do it.
--
Ron Ramirez
Ferdinand IN
Posts: 79
Threads: 8
Joined: Dec 2014
City: Wood River, Il.
(12-27-2014, 12:18 PM)klondike98 Wrote: Hi Chris, welcome to the Phorum! Unfortunately I can't answer your questions but since no one had responded yet I just wanted to welcome you and let you know there will likely be someone who can help.
Thank You
Bob. I appreciate the reply.
Chris H
N9WHH
Posts: 79
Threads: 8
Joined: Dec 2014
City: Wood River, Il.
(12-28-2014, 10:49 PM)Ron Ramirez Wrote: Chris
Send Phorum member Radioroslyn (Terry) a PM or email. As I recall, he has done this work before and can advise you on how to do it.
Thank You Ron...I will give him a PM. I appreciate the information.
Chris
Chris H
N9WHH
Posts: 79
Threads: 8
Joined: Dec 2014
City: Wood River, Il.
Hello All,
Well, after a lot of thought and trial and error, success at last! I spent several hours this afternoon in restringing the tuning condenser and tuning knob. It was not easy and I am not sure I could describe just what I did to someone else on the process, but it is working as it should with all the original components. Just a note to Radioroslyn; I appreciate your offer to help, but could never get a strong enough cell signal to make the call from my shop. Thanks again though.
Now on to other things; such as taking care of the electrolitics, and any out of spec resistors, and getting some fuses installed. Hopefully when I get the condenser back in it will play as well or better than it did when I started. Looking forward to the rest of the project.
Chris H
N9WHH
Posts: 178
Threads: 19
Joined: Feb 2014
City: The Motor City,Detroit MI
As far as cleaning the tuning dial, DO NOT use water! The ink is water soluble. I'm not sure what is a good cleaning method.
Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
 Glad to hear you got the tuner strung! Persistence pays off!
Posts: 79
Threads: 8
Joined: Dec 2014
City: Wood River, Il.
(01-19-2015, 09:50 AM)Kestas Wrote: As far as cleaning the tuning dial, DO NOT use water! The ink is water soluble. I'm not sure what is a good cleaning method.
Last night I experimented on one end, where the part number is etched on the dial band, with Gojo (w/o pumice). It did not affect the etched lettering as far as I could tell. So I let it sit there a little while before rubbing off; still no apparent change. After all, all that I wanted was to clean off 80+ years of goo and dirt. I went on and cleaned the entire band. It got off most of the crud...not perfect, but looks much better than it did. I am guessing that the brass has a lacquer finish on it and that is what protected the etching.
I did learn my lesson before, after washing the etching off a similar band on my Radiola 18.
Chris H
N9WHH
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM |
|
An attempt to remove the Field Coil from a G speaker
|
| Arran
Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I would unwrap the field coil, and see if maybe there a break near one of the ends, like where the coil wire att...Arran — 10:23 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| ...and this is what I did. I fed a little LT into the screwholes with a small brush, and a little on the rim next to the...morzh — 09:52 PM |
|
Philco 40-120C Restoration
|
| I combined the two 40-120C threads together as we like to keep the discussion of the same radio together. It helps with...klondike98 — 09:36 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| Just checked were I buy tubes price is four dollars. So living in Florid we have a local source for tubes. David David — 09:14 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| The higher voltage may be due to higher mains voltage. My mains run 120-125AC when the set was new mains would be 110-11...David — 09:09 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| Thank you for your reply. I pulled a speaker from a Philco 41-221 and received the same result. I used a signal tracer t...bluecap — 08:45 PM |
|
Philco 40-120C Weak, Distorted Ouput
|
| Have you tried a different speaker?
How did you trace the distortion?
How do you know it is weak? What is the reference?...morzh — 08:33 PM |
|
Philco 46-480 Electronic Restoration
|
| Amen to that! Every time I think I’ve captured them all, I realize that there’s another error. My goal is to finish with...jrblasde — 07:00 PM |
|
Who's Online
|
There are currently 3591 online users. [Complete List]
» 1 Member(s) | 3590 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
