Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

620 cabinet logo misplaced?
#1

hello:
we have a curious 620 cabinet, as the philco logo is set between the knobs and dial. not at the top like all of the pictures iv'e seen online.
the sticker inside of it says run #1
is this possibly a rarity? or could it be a misplaced decal from a restoration?
anyway to tell, or any info would be appreciated.
thank you.
   
   
#2

Neat! Icon_thumbup

That's an original decal. You can tell the difference between it and the Radio Daze PH8 by the fact that the 1932-36 originals had more of a copper color rather than gold.

I seem to recall that Philco's photos of this model show the decal as on your cabinet. I suspect that the very first 620B cabinets to be built had the decal placed there, before Philco decided to move the decal to the top edge as seen on most 620B cabinets.

As we all know, Philco was famous (infamous?) for their running changes in models. So it should not be surprising that those changes would extend to decal placement on cabinets as well.

--
Ron Ramirez
Ferdinand IN
#3

(01-03-2015, 10:01 PM)Ron Ramirez Wrote:  Neat! Icon_thumbup

That's an original decal. You can tell the difference between it and the Radio Daze PH8 by the fact that the 1932-36 originals had more of a copper color rather than gold.

I seem to recall that Philco's photos of this model show the decal as on your cabinet. I suspect that the very first 620B cabinets to be built had the decal placed there, before Philco decided to move the decal to the top edge as seen on most 620B cabinets.

As we all know, Philco was famous (infamous?) for their running changes in models. So it should not be surprising that those changes would extend to decal placement on cabinets as well.


Thanks for looking at it ron.
We will take care of it.

Icon_smile




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently no members online.

>