Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Model 112 Highboy
#1

I am looking at a Philco 112 Highboy. It's unrestored. The veneer is in good shape with a few scratches. It is one of the cabinets that Bel Geddes designed. Still has the label on the back of the cabinet. The owner is asking $195 which to me is high. What do you believe would be a fair price? I am out in the Portland OR area. Any feedback would be welcome. Thanks
#2

http://www.philcoradio.com/phorum/showth...p?tid=6087

One of the buys, $99, in 2013.

I say not above 130.

I bought a 111 a year and a half ago which shares the same chassis but is a highboy. $75.
#3

(02-14-2015, 10:32 PM)Umorzh Wrote:  http://www.philcoradio.com/phorum/showth...p?tid=6087

One of the buys, $99, in 2013.

I say not above 130.

I bought a 111 a year and a half ago which shares the same chassis but is a highboy. $75.

Thank you I appreciate the link and the feedback.
#4

Roy, too bad your not closer to AZ. I have a 112 restored I will be listing when I get back there. They are nice radios but I really don't want to worry about shipping them!
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#5

 I would say that $195 is way too much money for the majority of unrestored early 30's consoles. I say this because of where the market has gone not because I don't like them. Where I am, in which they are not nearly as common as the U.S midwest, anything over about $125 makes them a hard sell, and that's in good original condition. Almost all have just the single AM broadcast band, which ends at just over 1500 KC, it wasn't until 1932-33 that sets with a "police band" and shortwave became common. The other reason is because of the styling, even with the Norman Bel Geddes cabinets they are viewed as being old fashioned, and the dials and control panels are all sort of similar. It's a shame in one way in that they are not as appreciated, but then again that also makes them more affordable to those of us that like them.
Regards
Arran
#6

Difference is a questionable dinner for two and a few gallons of gas, so if you want a project take it.
#7

Unless stated otherwise, I found that all craigslist listings are negotiable.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM

[-]
Who's Online
There are currently 3554 online users. [Complete List]
» 2 Member(s) | 3552 Guest(s)
AvatarAvatar

>