1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
116b band swicth nob?
Fred Taylor
Phorum Expert
*****
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
#1

03-27-2015, 06:48 PM
     What Is the correct part for band switch? , round nob or a thumb lever  I have seen both , if it is the lever design what does it look like and was there felt washers behind the nobs?
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,248
Threads: 266
Joined: Dec 2009
City: Roslyn Pa
#2

03-27-2015, 07:25 PM
I'm not sure which goes on your set but there is a BS knob used only on some of the 1936 models. Here's a pic of it.
http://philcoradio.com/gallery/1936a.htm#y
That is what is on both of my 116X's. That was the best pic of that knob I found.
GL w/it
Terry
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#3

03-27-2015, 08:20 PM
I have also seen both the round black knob as well as the oddball bandswitch knob that was only used in the 1936 season (which Terry linked to above) on the early (shouldered) 116B, so I would say either one is OK.
--
Ron Ramirez
Ferdinand IN
Find
Fred Taylor
Phorum Expert
*****
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
#4

03-27-2015, 10:06 PM
(03-27-2015, 08:20 PM)Ron Ramirez Wrote:  I have also seen both the round black knob as well as the oddball bandswitch knob that was only used in the 1936 season (which Terry linked to above) on the early (shouldered) 116B, so I would say either one is OK.

THANKS FOR QUICK REPLY Icon_crazy
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2729 online users. [Complete List]
» 4 Member(s) | 2725 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios