Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

610B Cabinet
#1

When I brought this 610B home I posted a couple pics .  Now that I've finished the chassis (which went smoothly and has better reception than anything else I've worked on so far) I started cleaning up the cabinet.  I thought this was an original finish until I looked a little closer.  Now I'm thinking it may be the original finish with some extra lacquer or shellac added....  Here's a closer look at the side where it sure looks like someone added something to the finish ...or did they sometimes come from the factory with drips?  There are also some very dark finish areas and much lighter areas like something was stripped but not completely?  Thoughts?

[Image: https://www.dropbox.com/s/0mmmsrxbxy1tnf....jpg?raw=1]
#2

Sorry Bob, but that is either a very poor refinish, or as you suspect someone slopped on some shellac or something; you don't see drips and runs like that from the factory.   If it is just shellack you can try some denatured alcohol to remove shellac without damaging any original lacquer underneath.  Unfortunately judging from the dark splotches I think you'll need to do a strip and refinish.  The good news is the cabinet looks pretty solid so it should be fairly easy unless that is polyurethane on there. Good luck!

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#3

That's what I was think John, thanks!  I'm going to go ahead and strip it.  I really like this set.  The cabinet is indeed very solid and should come out looking nice.  I think the grill cloth may be original, its in decent shape...what do you think??  

[Image: https://www.dropbox.com/s/74vvkpicik4l1p....jpg?raw=1]
#4

Yes, that is original cloth. Icon_smile

--
Ron Ramirez
Ferdinand IN
#5

Thanks Ron! It will go right back into the set. Icon_thumbup
#6

That is just fowl!

Who the hockey stix would do that! Grrrrrr

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#7

Well the set was with the same owner since the 40s so I suspect that it was just an attempt to keep the set looking good. I think its a pretty old refinish or "finish freshener".
#8

I was finally able to get back to the 610B cabinet.  I had it stripped, toned and lacquered 6 months ago but just finished the final rub out and wax.  Put the chassis back in with all new rubber mounts and original grill cloth.  We're streaming Christmas carols on it now through the SSTRAN...Ho Ho Ho....
Stripping...stripped...finished
[Image: https://www.dropbox.com/s/5vynwli76n9qzi....jpg?raw=1][Image: https://www.dropbox.com/s/qm1cna560uxqww....jpg?raw=1][Image: https://www.dropbox.com/s/kav2ne8bnxpb44....jpg?raw=1]
#9

Beautiful job, Bob ! Congratulations. Now you can enjoy many years of music from it . Icon_clap
#10

Hello bob
Well I did one these some years ago but mine was
painted white with latex paint and
they used a pillow case for speaker grille
They went as far as painting the knobs
I had to strip and refinish to if you look in the philco photo section you will see mine
Anyway yours looks very nice also I found out this radio sounds great
And receives stations nicely
#11

Hey, radiorich - welcome back!! Icon_thumbup Icon_wave Icon_biggrin

And Bob - great job!! Icon_thumbup Icon_thumbup Icon_clap Icon_clap

I'm glad you gave it the original two-toning. I see so many that get refinished in a single color... Icon_thumbdown So it's always good to see them done right, like yours and Rich's. Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#12

Thanks guys, this was a fun one to do and did turn out nice.  Its been our Christmas player churning out carols from the SSTRAN. Rich, your radio was one of the example radios I used to tone mine.  The flash photo doesn't quite do it justice. I always go to Ron's photo gallery first for the best example of the radio.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2817 online users. [Complete List]
» 2 Member(s) | 2815 Guest(s)
AvatarAvatar

>