Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Hi guys,
I've run into a wall with this radio. All caps have been replaced. All resistors, coils and tubes have been tested and replaced as nec. I am able to do a complete alignment, but I have no FM reception at all  , not even static. AM works great!
What do you think?
Thanks,
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Hmmm...
Can you try injecting an FM IF signal along the FM IF path and see where it appears (or disappears)?
--
Ron Ramirez
Ferdinand IN
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Sounds good. I'll check it out and get back to you.
Thanks, Ron.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
I have no FM reception at all [Image: http://philcoradio.com/phorum/images/smi...on_eek.gif] , not even static.
Funny thing about that's how FM works No Static!!!
Your a glutton for punishment!!!
If you don't a Fm generator you can use an am signal
but use a tracer with a RF probe (diode detector) to follow
the signal around till you get to the limiter stage.
GL
Terry
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
OK, it appears that the signal goes in to the 1st IF trans and doesn't come out. It feels like the core is binding when I try turn it. Could the trans be bad? BTW, I have an exact replacement.
Thanks,
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
(This post was last modified: 05-12-2015, 05:02 PM by Eric Adams.)
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Possible but I'd measure the resistance across TC-6 Should have a very low resistance. I have had cores seize to the coil form and while trying to adj it has ripped the wires right off the coil render it useless.
Terry
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
The resistance was very low and matched with the spare that I have. Any other ideas?
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
(05-12-2015, 06:29 PM)Eric Adams Wrote: The resistance was very low and matched with the spare that I have. Any other ideas?
Well I think I'd just swap it out. Could have a bad cap across the winding. Only 4 wires not a big deal.
Terry
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Thanks. I'll give it a shot.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
OK, I replaced both 1st and 2nd IF transformers  No luck.
Any other ideas?
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Soooo where are you losing signal now?? Is it making it though the 2nd IF stage??
Terry
(This post was last modified: 05-19-2015, 09:24 PM by Radioroslyn.)
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
I was too frustrated to check. I'll check it tomorrow and let you know.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
I find FM stuff frustrating too!!!
Terry
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
Keep on plugging at it. You have my sincere sympathy; I restored a 48-482. Double and triple check all your connections. You'd be surprised how easy it is to look at something and see it as right one time, only to pick it up on a second look closely following the diagrams that show parts locations and wiring, and the schematic. Don't get frustrated. One thing about these old radios, when they don't work, something IS wrong. You'll find it eventually.
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Thanks mike. I know what you mean. I have restored two 48-482s and had less trouble. The set of schematics and pages of troubleshooting that is available for the 48-482 is fantastic and really helps with diagnosis. The 50-925 doesn't come close with their poor documentation.
I haven't given up yet but it is being punished for a while. It will sit on the shelf until I feel better about it.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Users browsing this thread: 8 Guest(s)
|
|
Recent Posts
|
|
Philco 46-420 Code 121 Reception issues
|
| Welcome Eric,
I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM |
|
Philco 46-420 Code 121 Reception issues
|
| You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM |
|
Philco 42-1008 conversion kit
|
| Interesting. I haven't seen that before.klondike98 — 07:02 PM |
|
12' Philco
|
| Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM |
|
Shadow Meter Bulb
|
| Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM |
|
Shadow Meter Bulb
|
| Ok. Thanks for the correction.RossH — 03:09 PM |
|
Model 28L
|
| For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM |
|
37-60 revision 6
|
| I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM |
|
Shadow Meter Bulb
|
| Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM |
|
Hickok AC51 tube tester
|
| Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
