Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 95 value
#1

Picked up a Philco 95 today.
Had been in the family since new.
Cabinet in exc. condition. No Loose veneer .
Appears that it has had some areas re-finished at some time.
Guy said it worked fine.
Brought it home and hooked it up to variac, and it play beautifully. No hum or static.
Receives signals strong through the whole dial.
Looks like original rayon covered cord to boot.
Bought this to re-sell.
Do not plan on removing the chassis.
Will just clean it up and sell.
What you Philco fans price this one at?

[Image: http://i1161.photobucket.com/albums/q509...2095-1.jpg][Image: http://i1161.photobucket.com/albums/q509...2095-2.jpg][Image: http://i1161.photobucket.com/albums/q509...2095-3.jpg]
#2

$85-120 where I am.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

 Something doesn't look right about the finish on the cabinet, for one thing it looks sort of dull, and it should be gloss. For another it doesn't look like there is any toner on the solid wood parts, like the legs, the moldings, and the edges of the cabinet doors. On my model 96 lowboy it also had this fogging effect around the edges of the front panels, and the sides of the cabinet were finished with a dark walnut lacquer. I think that someone stripped your cabinet at some point and refinished it. It's unfortunate that the photo of the model 95 highboy is of such a poor example in terms of getting the shading effect, it looks dirty or like someone smeared oil stain all over it.
Regards
Arran
#4

Yeah. Here is an original finish from a CL ad. You can see, though yellowed, the trim and legs are darker.

   

Now the same radio refinished:

   

Well after looking at his again, I suppose they could have used less toner on the top. Or maybe just the top was refinished. The legs look about right. But the white wood trim to the left and right should have been toned darker on top and bottom leaving a lighter area in the center (vertically).

That is the original finish on the bird's eye front and the inside of the doors. So I matched that level of gloss in the refinish of the rest. It probably had more gloss when new.

I think I gave $90 for this one, which was probably $40 too much as it was in the CL ad.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1388 online users. [Complete List]
» 1 Member(s) | 1387 Guest(s)
Avatar

>