Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 46-1201 Phono Cartridge
#1

See post #3 below for information on a cartridge for a Philco 46-1209 radio-phono.

Meanwhile, enjoy some photos of Greg's 46-1209 with gold accents on the knobs, hand applied.

- admin



   

   

   

   

   

Greg V.
West Bend, WI
Member WARCI.org
#2

May I ask where one may locate a replacement needle and cartridge for a Philco 46-1201? I love this model and the technology involved. And it's one of my most wanted units.  

Ian M. Gordon
NEARC
HARPS
#3

This is the go-to place for cartridges and idler wheels for me: http://www.thevoiceofmusic.com/

I hand painted the gold on the knobs of my 46-1201. Really dresses them up. I do that on Hippo models too, which use the same knobs.

Greg V.
West Bend, WI
Member WARCI.org
#4

That model No. from VM is KCCC. It's a barrel type with both 78 and LP styli. It has a higher output voltage than other's you might use. I believe the output volts. are 1.3 volts. I just ordered one yesterday.
#5

Since Jim added some useful information regarding the phono cartridge for this model, I decided not to delete the entire thread, even though the radio has been sold. I will leave it up to the moderators if they wish to leave this thread or delete the whole thing.

Greg V.
West Bend, WI
Member WARCI.org
#6

Per Greg's suggestion, I have converted this thread from a "for sale" ad into a restoration topic.

--
Ron Ramirez
Ferdinand IN
#7

Thanks, Ron.

Greg V.
West Bend, WI
Member WARCI.org




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 3438 online users. [Complete List]
» 1 Member(s) | 3437 Guest(s)
Avatar

>