1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 45 wiring
jmac3ky
Member
***
Posts: 65
Threads: 23
Joined: Mar 2013
City: Murray, KY
#1

05-16-2015, 10:00 AM
Restoring a Philco 45C. I think the 45L electronics would be similar. Looks like it has been serviced many times in its 80-year life, including wire rerouting. The schematic has been of some help. But, there are still issues in the RF wiring.

Does anyone have a 45 chassis that still has the band switch, antenna and oscillator coils wired in place? I've looked at online restoration photos but the fiberboard 2x4 connection platforms always cover some of the areas I need to see.
Normally I would give up the ghost on one such as this, but it has the beautifully designed Butterflly cabinet.

Any information would be appreciated. Thanks.     John
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

05-16-2015, 06:48 PM
I don't have one but Kirk does.
Terry
Find
morzh
Odobenus rosmarus
*****
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#3

05-16-2015, 09:26 PM
Tell-tell....
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
jmac3ky
Member
***
Posts: 65
Threads: 23
Joined: Mar 2013
City: Murray, KY
#4

05-18-2015, 12:52 PM
(05-16-2015, 06:48 PM)Radioroslyn Wrote:  I don't have one but Kirk does.
Terry

Thanks Terry.

I've contacted Kirk (Oldrestorer) and he has been helping me rewire the bandswitch, oscillator coil, and antenna coil the way it came from the factory. In addition to photos from his two sets, he drew out a nice sketch of the wiring.

I have to admit, Kirk's the last of the good guys.

John
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#5

05-18-2015, 07:01 PM
Your welcome!

Terry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 6779 online users. [Complete List]
» 2 Member(s) | 6777 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration