Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

E.H.Scott Military Receiver RCH
#1

Here is a receiver that I friend in Illinois gave me. He had no idea of what it was. I think its a E.H. Scott RCH receiver. Here are some pictures..
[Image: http://i292.photobucket.com/albums/mm38/...xor1cg.jpg]
[Image: http://i292.photobucket.com/albums/mm38/...c5nrtk.jpg]
[Image: http://i292.photobucket.com/albums/mm38/...0dhu0d.jpg]

No markings on it anywhere .. Its missing the name plates..

It seems to match this picture of a RCH..
[Image: http://i292.photobucket.com/albums/mm38/...sa8pug.jpg]

Can anyone positive ID this?

Thanks
Skip...
#2

No expert on these Skip but the chassis picture on the RCH sure appears to match what you have perfectly as far as I can see.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#3

Better keep up on ur vitamins!!! Looks like a backbreaker!!!!
Don't know much about your rx. Have seen a few over the years but never took one home.
You may try the ARC-5 forum over at yahoo. They discuss some other military stuff other than ARC-5 stuff.
Terry
#4

Ok thanks for the info.. Its built like a tank.. Covers ..

[Image: http://i292.photobucket.com/albums/mm38/...tbyox6.jpg]

I think it was used on Navy ships. Receives well. I did download the manual.. I am going to do a full alignment and then probably sell it.. No room for it as I have my 2 R-390's , the Collins R-388 and a Big old Hallicrafters SX-101 RX and the HT-32 Transmitter.. which take up a lot of room..


Thanks
Skip...
#5

Tis easier to buy a bigger house.  

Terry
#6

    These were also used in a Mackay shipboard communications console after the war, under the designation SLR-F.
#7

Very Interesting..

Thanks
Skip...




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>