Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

E.H.Scott Military Receiver RCH
#1

Here is a receiver that I friend in Illinois gave me. He had no idea of what it was. I think its a E.H. Scott RCH receiver. Here are some pictures..
[Image: http://i292.photobucket.com/albums/mm38/...xor1cg.jpg]
[Image: http://i292.photobucket.com/albums/mm38/...c5nrtk.jpg]
[Image: http://i292.photobucket.com/albums/mm38/...0dhu0d.jpg]

No markings on it anywhere .. Its missing the name plates..

It seems to match this picture of a RCH..
[Image: http://i292.photobucket.com/albums/mm38/...sa8pug.jpg]

Can anyone positive ID this?

Thanks
Skip...
#2

No expert on these Skip but the chassis picture on the RCH sure appears to match what you have perfectly as far as I can see.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#3

Better keep up on ur vitamins!!! Looks like a backbreaker!!!!
Don't know much about your rx. Have seen a few over the years but never took one home.
You may try the ARC-5 forum over at yahoo. They discuss some other military stuff other than ARC-5 stuff.
Terry
#4

Ok thanks for the info.. Its built like a tank.. Covers ..

[Image: http://i292.photobucket.com/albums/mm38/...tbyox6.jpg]

I think it was used on Navy ships. Receives well. I did download the manual.. I am going to do a full alignment and then probably sell it.. No room for it as I have my 2 R-390's , the Collins R-388 and a Big old Hallicrafters SX-101 RX and the HT-32 Transmitter.. which take up a lot of room..


Thanks
Skip...
#5

Tis easier to buy a bigger house.  

Terry
#6

    These were also used in a Mackay shipboard communications console after the war, under the designation SLR-F.
#7

Very Interesting..

Thanks
Skip...




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4096 online users. [Complete List]
» 2 Member(s) | 4094 Guest(s)
AvatarAvatar

>