Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

TWO 16b tombstones/ FINISHED!
#46

 Not sure Art, If I  remember right I was told that they used both styles of nobs and there for didn't matter. I also looked at a bunch of 16bs online and seen both styles of nobs on both early and late versions. Ron would know for sure, I think Ron would have given me a Icon_thumbdown  if there where a discrepancy in that department Icon_think   
#47

Quote: I think Ron would have given me a [Image: http://philcoradio.com/phorum/images/smi...mbdown.gif]  if there where a discrepancy in that department [Image: http://philcoradio.com/phorum/images/smi..._think.gif]   
Yeah, I got "thumbs down" on knobs one time. Icon_lol    Seriously, I'm happy to have Ron critique my work.
Steve

M R Radios   C M Tubes
#48

  I just noticed I have 4 stars now under my belt (senior member Icon_think ) Icon_clap Icon_crazy Icon_crazy Icon_crazy Icon_crazy Icon_crazy  I don't see how when I cant apply decals properly Icon_think
#49

(06-14-2015, 11:35 PM)Fred Taylor Wrote:    I just noticed I have 4 stars now under my belt (senior member Icon_think ) Icon_clap Icon_crazy Icon_crazy Icon_crazy Icon_crazy Icon_crazy  I don't see how when I cant apply decals properly Icon_think

HeHe.. The stars depends on how many times you have posted on here.
#50

Hi,

Very nice job on the model 16Bs.. two of my favorite radio models.

I have seen the late 16B with either three lower older-style hex knobs or three of the newer styled round knobs. The upper knob on the late set should always be the newer concentric style (the older hex style knob would not fit!). Same goes for the 16X versions from June & Nov 1934.

Now, having seen this mix of knobs on some later versions does not make it certain that they came from the factory this way, though it seems likely, as so many of the late models are seen this way.

One other point that just occurs to me, seeing Fred's empty cabinets side by side. The upper knob cut-out for the later set has larger diameter than for the earlier set, as needed to accommodate the concentric knobs of the later chassis versus the single retractable knob of the earlier version. Has anybody noticed if the later-cabinets fitted with earlier chassis had the smaller diameter cut-out?? This would for sure indicate they must have come from the factory this way. The converse does not necessarily prove anything, of course.

Paul
#51

Those 16B's look absolutely exquisite! Fantastic job!

Slave to an RCA Victor CTC-25




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 5254 online users. [Complete List]
» 1 Member(s) | 5253 Guest(s)
Avatar

>