Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1960's Panasonic from an estate sale
#1

I was at an estate sale today, and I saw this real nice Panasonic RE-7371. It was just begging me to take it home, and for $10, I just couldn't pass it up. It's in excellent condition, and it sounds beautiful. It's pretty nice to be in the FM world again, too.

   

Slave to an RCA Victor CTC-25
#2

For 10 bucks, sure, could always use another tuner.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

I hit it with the old GOJO Creme, and YOWZA! That GOJO Creme made it look like brand new!


Attached Files Image(s)
   

Slave to an RCA Victor CTC-25
#4

Better than any AM/FM you could get today for the money. Why was it filmed on the toilet tank?

Paul

Tubetalk1
#5

Didn't you know I collect toilets? These are three of my nicest Kohlers.


Attached Files Image(s)
   

Slave to an RCA Victor CTC-25
#6

My 1959 Kohler Wellworth. Sorry, I couldn't get all three in the picture.


Attached Files Image(s)
   

Slave to an RCA Victor CTC-25
#7

And vintage vacuums I see too. Many plumbers in my family, they were all skeptical of the low flush toilets. A vintage bowl was a quality bowl. I have seen how the vitreous is made and fired and I find it very interesting.

Paul

Tubetalk1
#8

Is there any particular reason why when I click this radio off, it blasts the station back at me for about 2 seconds and slowly fades away? Sometimes it changes stations during the fade. It works great, but this is getting annoying. The blast is so loud, it can be heard on the other side of the house. I'm scared it's going to hurt the speaker if it continues.

Slave to an RCA Victor CTC-25
#9

 First of all it is not from the 1960s, probably more like the early 1970s, before 1970 the Jap makes used to mark the dial frequencies in KC and MC not KHz and MHz, if you open it up you may find some date codes that will narrow it down. As for the other issue with the volume blast when you turn it of chances are it needs the electrolytics changed and maybe a few resistors by now.
Regards
Arran




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

[-]
Who's Online
There are currently 6349 online users. [Complete List]
» 2 Member(s) | 6347 Guest(s)
AvatarAvatar

>