07-05-2015, 06:48 PM
1939 Stromberg Carlson 430-H Restore on YouTube
07-10-2015, 01:57 PM
Hello Phorum:
Part 3 of my 1939 Stromberg Carlson 430-H series now uploaded. A link below is for anyone interested...thanks https://www.youtube.com/watch?v=hCQscu93wDw
07-17-2015, 01:40 PM
Hello Phorum:
Part 4 of my 1939 Stromberg Carlson 430-H series now uploaded. A link below is for anyone interested...thanks https://www.youtube.com/watch?v=90mMj-etfiY
07-19-2015, 08:59 AM
That was a close shave for ole' Dickel.
Your cap restuff looks pretty good, but they sell hot glue that is a more tan/brownish color that would look a little better. Good work and thanks for the videos! John KK4ZLF Lexington, KY "illegitimis non carborundum"
08-02-2015, 01:17 PM
Hello Phorum:
Part 5 of my 1939 Stromberg Carlson 430-H series now uploaded. A link below is for anyone interested...thanks https://www.youtube.com/watch?v=dasIPycCWlE
08-02-2015, 03:10 PM
Interesting and entertaining video as always.... thanks!
Congratulations on the potato contest! John KK4ZLF Lexington, KY "illegitimis non carborundum"
08-07-2015, 10:32 AM
Hello Phorum:
Part 6 of my 1939 Stromberg Carlson 430-H series now uploaded. A link below is for anyone interested...thanks https://www.youtube.com/watch?v=rnXTrM-pe7Q
08-07-2015, 10:32 AM
08-08-2015, 02:26 AM
Buzz;
A lot of 1936-38 RCA sets used a similar chassis isolation system to your Stromberg Carlson, fortunately most of the ones I have found are still usable. The closest thing that I have seen to that "T" nut and washer was something a representative of a hardware supply company demonstrated at a car show, it was an insert that you could use in sheet metal to hold a machine screw. I don't know what the proper name of these inserts is but the device he used was something like a pop riveter that would expand part of it so it would not come out. If I remember I will go down to their store and ask them about them. Regards Arran P.S The cabinet top is warping because there is veneer on the bottom side, which is also still sealed, but none on the top. So the boards that make up the cabinet top can absorb moisture and dry out faster on the side where the veneer was removed. When you re-veneer the top and seal it again it should stop doing that, but to flatten it out just wipe it down with a damp rag and clamp it first.
08-08-2015, 10:51 AM
arron
their is a tool called nut-insert looks like pop rivet gun you screw a post in an then nut-insert squeeze handle. bends top over a little easy said then done buzz if you want to try it I will loan you mine great job on potatoes johns a sore looser sam Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift mafiamen2
08-08-2015, 11:56 AM
(08-08-2015, 10:51 AM)sam Wrote: arronThanks guys for your suggestions, but I've figured a way to do it. Watch next Fridays video as I will show in detail....Buzz PS ,,I think John learned the real way to grow potatoes from me..haha
08-08-2015, 11:58 AM
(08-08-2015, 02:26 AM)Arran Wrote: Buzz; Good explanation as to the warping...It was very hot in the garage and muggy....thanks, buzz
08-14-2015, 11:18 AM
Hello Phorum:
Part 7 of my 1939 Stromberg Carlson 430-H series now uploaded. A link below is for anyone interested...thanks https://www.youtube.com/watch?v=B0eMxAwTC2A
08-15-2015, 12:30 PM
buz
hmm what happen to 1157 ? great video as always that screw driver is that for the philco centric cone alignment if so can I get a close up of it thanks sam Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift mafiamen2
08-15-2015, 12:54 PM
Another great video Buzz!
You sure are getting a lot of use out of that pencil sharpener John KK4ZLF Lexington, KY "illegitimis non carborundum"
« Next Oldest | Next Newest »
Users browsing this thread: 2 Guest(s) |
|