Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-395 Transformer Help
#1

I am in the process of repairing a 42-395 for a customer that had plugged it in and turned it on before he brought it in.  Therefore the Power & output transformers are cooked as well as associated wiring and rectifier socket.

One thing I do know is the transformer only has 2 secondary windings. It has a hv center tapped winding and a 6.3vac 4-5 amp winding. This unit uses a 7Z4 rectifier and 7C5 audio outputs have replaced the 7B5.

I would like to know how to calculate the voltages to find a transformer that will be close.

Any & all help is appreciated
Thanks
Jason
#2

Well you can figure about 10ma per tube for the HV except for the output (20ma ea) and the 7Z4 (0 ma). That puts you at about 90ma. Voltage wise you need about 200vdc so figure 250-0-250vac.

Terry
#3

Hey Terry Thanks so much. I was leaning toward a 500vct transformer.  The problem with modern transformers is that the 6.3vac winding usually is not high current.  In this model the 6.3vac winding needs to supply around 5 amps including lamps and rectifier.  I have found 2 that might work:
I have found an edcor transformer # XPWR093 it is 500vct @ 300ma, 6.3vct @ 7A.
I know the 300ma is probably overkill, but would this work?
Also found edcor# XPWR072 550vct@250ma, 6.3v @ 7A. The 275-0-275 maybe a bit  too high though.
#4

The original power transformer part # is 32-8192

HV secondary: 640 VCT @ 90 mA
Filament: 6.3V @ 4.5A

Output transformer is 32-7997

Primary impedance 12,000 ohms push-pull
Secondary impedance 5 ohms with a 7% feedback tap
10 watts
Turns ratio 46:1

From the 1946 Philco Quick Selector Parts Directory

--
Ron Ramirez
Ferdinand IN
#5

You can always lose the rectifier tube and use diodes instead which will reduce filament load. Also it is unusual to have both power and output transformers fail (at the same time?) Nothing to lose by partially disecting and look for corroded connections; output transformers are notorious for this.
#6

Thanks Ron for the info.  With this info. I was able to find a replacement Hammond or edcor.  

I Appreciate all the help.  

I found a replacement tranny that will supply 5A @6.3v. This gives a little wiggle room and if I use #47 lamps the current will be 200ma less.

This model also has prewar fm.  So I will be building a converter for it also.

Maybe I can track down a 10 button faceplate, as usual the plastic has shrunk and pulled out the screws.  
Thanks
Jason




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
The list of my radio & TV collection!
Peter; I can't say for certain but many North American made radios from that era, the late 1940s onward, had silver m...Arran — 02:06 AM
Philco 39-7C Restore
A little more work today. I got the first IF transformer back together after replacing the wiring going to the 78 tube ...klondike98 — 12:06 AM
Two small radios from France. Restoration and review.
And here they are, the French beauties ready: In summary, the suspicion that radio transmits the national cha...Vlad95 — 10:46 PM
Two small radios from France. Restoration and review.
One is ready for washing, the other for painting: ATTENTION Faint-hearted and heart patients, please d...Vlad95 — 10:36 PM
Two small radios from France. Restoration and review.
Range Switch Block: I thought that mica capacitors of this type died out in the 30s, but no, they just moved ...Vlad95 — 10:29 PM
Two small radios from France. Restoration and review.
Chassis bottom view: Again, like twins, especially in the range switch part. Front panels: And...Vlad95 — 10:25 PM
Two small radios from France. Restoration and review.
Chassis removed, front view: Chassis rear view: It will be enough for the first device to prescribe a bath. Bu...Vlad95 — 10:11 PM
Two small radios from France. Restoration and review.
France Peculiarities of national character. Excelsior-52 threw me off track. It was too far outside my established...Vlad95 — 10:06 PM
Philco 16b no shortwave reception
First let thank everyone who helped ID this radio a few weeks ago! I have replaced all the capacitors and was able to r...Ken D. — 08:07 PM
Philco model 38 code 121 not receiving signal.
Ah yes, the Philco "Green Death" strikes again, someone suspected that cellulose nitrate based insulation migh...Arran — 06:23 PM

[-]
Who's Online
There are currently no members online.

>