Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 60 4th style?
#1

Does anyone make the correct speaker cloth for this cathedral? The label only says Model 60, not 60B, etc...

The one I'm contemplating buying has nice cloth, but has a pinkie finger sized stretched dimple in the cloth, supposedly, not a hole. I may need to replace the cloth or attempt to moisten that spot and shrink it with a hair dryer, if that's possible.

Any thoughts?
#2

Which 60 are you planning on buying? See Ron's page of versions of cabinets: http://www.philcoradio.com/tech/60evol.htm

I know the 60MB is not reproduced but I did find a cloth online that was pretty close.
#3

(10-27-2015, 11:08 PM)klondike98 Wrote:  I know the 60MB is not reproduced but I did find a cloth online that was pretty close.

Where did you find it, Bob? I have a 60MB that will be needing some cloth...

--
Ron Ramirez
Ferdinand IN
#4

Bob,
It's the one on the right side marked July '34 or the one on the left, second row marked June'35. That's the style cloth.
Steve
#5

SteveG

You want GRC05 from Radio Daze.

http://www.radiodaze.com/grille-cloth-05-item-grc05/

Incidentally, the greenish lines should be vertical, not horizontal as shown in the Radio Daze photo.

--
Ron Ramirez
Ferdinand IN
#6

Ron, I believe this is it
http://m.ebay.com/itm/391304815386

Its not perfect but not bad. Here it is in my MB
http://philcoradio.com/phorum/showthread...8#pid90228
#7

Thanks Ron. Now to get that radio home. Anyone have thoughts about shrinking the stretched spot before I have to consider replacing the grille cloth??
#8

Hey,
How big is the indent and how deep?
Shrinking the fabric is doubtful but you may be able to press it flat and iron it between 2 towels or pieces of fabric.
Just be cautious that the old glue may stick to the piece it is attached to so be careful.

Me

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#9

Thank you, Bob, for the info. Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#10

Kirk,
It looks like it's about 1/2"-3/4" in diameter and maybe 3/8" deep. I think between two moist towels with the iron might be the trick. Steaming is how they tighten seat material at the upholstery shop my friends run... I was worried that if I sprayed liquid on the cloth and then used the hair dryer, it would release 80 years of soiling from the cloth and stain it. I added a picture of the radio. Not the clearest, but it's the best I have right now.
Steve
[Image: http://www.surfacezero.com/g503/data/500...280369.JPG]
#11

Hey Ron, I was able to track down the order I made for the 60MB grille cloth and it was from the same vendor but may be a slightly different cloth than what I posted above.  See:

http://www.ebay.com/itm/ANTIQUE-RADIO-GR...5b1b358b18

This one looks a little different in his photos ...  hard to tell by viewing on line but I think this one looks more like the original cloth than what I posted earlier.  Anyway...the above (or the 12 x18 version of it) was what I bought.  Sorry for any confusion.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>