Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

zenith 6s27 restore/FINISHED!
#1

Started on this zenith 6s27, got the radio playing real nice. The cabinet was more than I bargained for the veneer on the front control panel was coming apart after stripping cabinet and have no choice but to replace the veneer. Here are some pictures of that process that I take Icon_eek


Attached Files Image(s)
                   
#2

Nice looking set Fred!
Can't have too many clamps.

What type/kind of glue do you use for jobs like this?

Tim
#3

Just finished the cabinet today, although the zenith cabinet still will get a fresh coat of zenith blue on the inside.The zenith is playing strong and will get new grill cloth as well with newly refinished nobs.


Attached Files Image(s)
       
#4

Nice as always Bud!

Crist
#5

As usual Fred, what a great job. You work quick!
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#6

Finished up zenith 6s27 tombstone today and pleased with the results. Very nice looking radio and will be a keeper to add to my collection of fine antique radios


Attached Files Image(s)
                   
#7

Few more pictures


Attached Files Image(s)
           
#8

As usual, your terrific job!

A friend in need is a pest!  Bill Slee ca 1970.
#9

Looks just like it rolled off the factory floor - no better and no worse.  That's the highest compliment I can give for a cabinet resto Icon_thumbup

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#10

(11-07-2015, 10:21 PM)Eliot Ness Wrote:  Looks just like it rolled off the factory floor - no better and no worse.  That's the highest compliment I can give for a cabinet resto Icon_thumbup

Thank you Eliot for the complement , I try to do the best I can with with the tools I have, enjoying restoring these radios. I wish i had a full time job doing them Icon_e_biggrin . Thanks every body else for the kind words.
#11

Wow! Super nice outcome as always. Looks like it just came out of the Zenith factory!  Icon_thumbup Icon_thumbup Icon_clap Icon_clap
#12

(11-08-2015, 10:05 AM)PhilcoJohn Wrote:  Wow! Super nice outcome as always. Looks like it just came out of the Zenith factory!  Icon_thumbup Icon_thumbup Icon_clap Icon_clap

Thanks John, sounds pretty darn good Icon_biggrin




Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5573 online users. [Complete List]
» 3 Member(s) | 5570 Guest(s)
AvatarAvatarAvatar

>