Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

zenith 6s27 restore/FINISHED!
#1

Started on this zenith 6s27, got the radio playing real nice. The cabinet was more than I bargained for the veneer on the front control panel was coming apart after stripping cabinet and have no choice but to replace the veneer. Here are some pictures of that process that I take Icon_eek


Attached Files Image(s)
                   
#2

Nice looking set Fred!
Can't have too many clamps.

What type/kind of glue do you use for jobs like this?

Tim
#3

Just finished the cabinet today, although the zenith cabinet still will get a fresh coat of zenith blue on the inside.The zenith is playing strong and will get new grill cloth as well with newly refinished nobs.


Attached Files Image(s)
       
#4

Nice as always Bud!

Crist
#5

As usual Fred, what a great job. You work quick!
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#6

Finished up zenith 6s27 tombstone today and pleased with the results. Very nice looking radio and will be a keeper to add to my collection of fine antique radios


Attached Files Image(s)
                   
#7

Few more pictures


Attached Files Image(s)
           
#8

As usual, your terrific job!

A friend in need is a pest!  Bill Slee ca 1970.
#9

Looks just like it rolled off the factory floor - no better and no worse.  That's the highest compliment I can give for a cabinet resto Icon_thumbup

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#10

(11-07-2015, 09:21 PM)Eliot Ness Wrote:  Looks just like it rolled off the factory floor - no better and no worse.  That's the highest compliment I can give for a cabinet resto Icon_thumbup

Thank you Eliot for the complement , I try to do the best I can with with the tools I have, enjoying restoring these radios. I wish i had a full time job doing them Icon_e_biggrin . Thanks every body else for the kind words.
#11

Wow! Super nice outcome as always. Looks like it just came out of the Zenith factory!  Icon_thumbup Icon_thumbup Icon_clap Icon_clap
#12

(11-08-2015, 09:05 AM)PhilcoJohn Wrote:  Wow! Super nice outcome as always. Looks like it just came out of the Zenith factory!  Icon_thumbup Icon_thumbup Icon_clap Icon_clap

Thanks John, sounds pretty darn good Icon_biggrin




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>