Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Unknown Philco
#1

All, Please ID this Philco..I picked this up at Kutztown a couple of years ago from Kirk I think.. Cannot remember the model Number..


It has 11 Tubes..

[Image: https://farm5.staticflickr.com/4599/3855...d11f_b.jpg]

[Image: https://farm5.staticflickr.com/4736/3855...7d89_b.jpg]

[Image: https://farm5.staticflickr.com/4685/3855...cc65_b.jpg]

Thanks

Skip..
#2

Try 111.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

I do not think so. The bottom doesn't match what I have..

Skip...
#4

It's a late version 112 using two 47 output tubes. Notice the two Mershons and the smaller multi-section filter cap can.

--
Ron Ramirez
Ferdinand IN
#5

This is 112.

111 has large cap can.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Superior 450 schematic
I need a schematic for this tube tester.daveone23 — 05:00 PM
Philco model 38 code 121 not receiving signal.
>> Yes. Ball up in a corner and cry very deeply? It's a good start :lol: Then try to get off the outer shell...morzh — 02:54 PM
Philco model 38 code 121 not receiving signal.
Yes. Ball up in a corner and cry very deeply? :P  :lol: I've never rewound a coil so first time for everything I guess....Stormlord5500 — 01:58 PM
Philco model 38 code 121 not receiving signal.
Well, you know what to do then.morzh — 01:27 PM
Philco model 38 code 121 not receiving signal.
Well I found it and it's not good. The primary of the antenna coil is shot.The famous (or infamous) Philco coil rot got ...Stormlord5500 — 11:58 AM
Atwater Kent 708 Flexible Resistor Identification Needed
Tony Could you possibly trace the flexes to where they go in your chassis? Should'nt be too hard.morzh — 09:23 PM
Atwater Kent 708 Flexible Resistor Identification Needed
None of the diagrams that are shown online are the same as what I have drawn. It is my setup with the two resistors conn...Tonym4704 — 08:47 PM
Atwater Kent 708 Flexible Resistor Identification Needed
morzh You are right. Scematic 808 is corresponded requered. On this case Purple - R11A 160 ohms Red - R11B 160 ohms Bu...Vlad95 — 08:07 PM
Atwater Kent 708 Flexible Resistor Identification Needed
Have you looked in here? And in here. 708, 808 and 808A are very similar.morzh — 07:43 PM
Atwater Kent 708 Flexible Resistor Identification Needed
Hello, That diagram in Rider's is a little different from the setup that I have. Note that the R11 resistor connects to...Tonym4704 — 07:37 PM

[-]
Who's Online
There are currently 2240 online users. [Complete List]
» 2 Member(s) | 2238 Guest(s)
AvatarAvatar

>