1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
1937 zenith radio dials. Found.
murf
Senior Member
****
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
#1

11-13-2018, 08:51 PM
Hello,
Does anyone know of a supplier of reproduction dials for 1937 zenith consoles?
I need the tone and local/distant dials for my 10s155 and have never seen any reproductions of these small white dials.
They usually break the top 2 dials taking the chassis out of the cabinet.
Anyone know of a supplier?
Thanks,
murf
(This post was last modified: 11-17-2018, 08:57 PM by murf.)
Find
NostalgiaRadioTime
Super Moderator
******
Posts: 1,521
Threads: 240
Joined: Sep 2012
City: West Bend, Wisconsin
#2

11-13-2018, 09:04 PM
Hi Murf,

I know I got some for the 1938 Zenith chassis from Radio Daze. Are any of these correct?

http://www.radiodaze.com/dials-plastic-o...red&page=2
Greg V.
West Bend, WI
Member WARCI.org
Website Find
KCMike
Phorum Expert
*****
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
#3

11-13-2018, 09:05 PM
Looking for something like this?
http://www.radiodaze.com/zenith-cntrl-di...m-ds-a437/
Find
murf
Senior Member
****
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
#4

11-17-2018, 08:56 PM
Yes, they have them in sets of 4.
I ended up ordering just the ones i need from Mark Oppat.
Thanks,
Murf
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4.RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2976 online users. [Complete List]
» 3 Member(s) | 2973 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)