Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Which model is this?
#1

I haven't been able to find the model number or any photos online of this exact kind. Any help would be appreciated. Thank you.
And it looks like some photos are upside down, don't know why. Sorry.


Attached Files Image(s)
               
#2

Hello and welcome.

Assuming you mean the large console (floor model) radio, it is a Canadian model 53 (CHASSIS TYPE 53 on metal tag = model 53). It does not correspond to any USA Philco models, so finding service information will be difficult. Not impossible, mind you, but difficult. You will need to obtain the Radio College of Canada set of manuals in CD format, sold on the auction site.

We normally do not allow ads in this section, but since this is informational only - you need the information and I am only glad to pass it on to you - here's a link where you can get your own CD.

https://www.ebay.ca/itm/193093192924

Good luck.

Edit: There is a black and white illustration of a Canadian model 53X (your set) at this page in the Philco Library section of this website - scroll almost all the way to the bottom of the page to see it:

https://philcoradio.com/library/index.ph...in-canada/

You will also note by looking at this page (also in the Philco Library) that the 53X/53AX is a 1942 model.

--
Ron Ramirez
Ferdinand IN
#3

Thank you very much. This helps me lots.
#4

Hi and welcome to the Phorum,
Give this a try: https://radio.codegods.ca/node/7036
Ignore the warnings.

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Welcome to the Phorum!
Icon_wave




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 3336 online users. [Complete List]
» 3 Member(s) | 3333 Guest(s)
AvatarAvatarAvatar

>