Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1940’s 38-5X
#1

I’m looking at a beautiful radio — very little cosmetic damage — I’m sure it’s a 38-5X. Still works, No Idea what I should offer to buy it. I have pictures. 

Thoughts?

Many thanks!            
#2

The little make an offer tag may mean "we have no clue". Maybe 50 bucks?

Set a ceiling, start low, you can always go up. Explain it will take time and money to make it play safely.

Good luck.

Paul

Tubetalk1
#3

Hi Herb and welcome,

Rub your hand down sides right close to front where the veneer curves around to the front. What you are feeling for is roughness or small cracks in the veneer around the bend. If this is the case it's trouble. I think I see it in the picture on the right side. To repair it's replacing the effected veneer and maybe the substrate (big job). For me that would be a no sale.

Good Luck!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

And by all means, DO NOT operate the radio even if it does still work. Old components love to release the magic smoke! If you get it replacement of caps and resistors is the rule before powering it up again. Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#5

Thank you for the Great advice. I appreciate it very much.
#6

Well folks, it will be a while before I’m back in Laramie, so this radio is fair game for anyone who’s interested. The owner tells me her sales philosophy is that a thing is worth whatever somebody is willing to pay...

You’ll find it at Aphrodite’s Emporium on E Grand Ave. in Laramie Wyoming. Tell Vi you heard about it from Herb.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2136 online users. [Complete List]
» 1 Member(s) | 2135 Guest(s)
Avatar

>