Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New here
#1

Just had come my way a Philco Radio so while hunting out some info found this site ,seemed a good idea to join

I have been collecting and fixing Vintage electronics for many years now
#2

Welcome to the Phorum! You found the right place for Philco radios in particular, but also most every other brand built as well. Lots of friendly folks here willing to help any way we can. Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#3

Hi and Welcome aboard, 

What sort of Philco set did you find a US or Brit built one? It's always a treat to see the non US set as they are pretty common over here. Especially the pre war models.
Here at the Philco Phorum Philco's are our speciality!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

Welcome!

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

Welcome to the Phorum!
Icon_wave
#6

Welcome to the Phorum. Like the handle "Fixitnow" is better than laterIcon_smile.

Paul

Tubetalk1
#7

Hello FIXITNOW,
Welcome aboard and glad to see you found your way here .
So What kind of Vintage equipment do you like collecting or working on ?

Sincerely Richard
#8

I have about 8 sets that need to be fixed "now". Paul

Tubetalk1
#9

Welcome to the website, Hope to hear from you now and then.  Icon_wink
#10

Welcome to the Phorum. David
#11

Hello Fixitnow,
Welcome aboard !
Sincerely Richard
#12

Welcome to the Phorum FIXITNOW Icon_wave

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"




Users browsing this thread:
[-]
Recent Posts
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Hello PittsburghToast , Welcome aboard and it looks like gary may have something for you ! now if I dig through my se...radiorich — 11:35 PM
Model 80 Antenna Issue?
You are kind of on the right path. You can touch the grid cap of the Detector/Oscillator 36 tube. I'm expecting a respon...RodB — 08:48 PM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Welcome to the Phorum, PittsburghToast!  I found an old thread that my interest you regarding the quality and worth of P...GarySP — 08:48 PM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Welcome to the Phorum! :wave: We do not have anything on that unit in our digital library. There is a Sam's Photof...klondike98 — 08:47 PM
Model 80 Antenna Issue?
I’ve replaced all the caps and resistors and the radio is working but minimal volume unless I put my hand near the re...Hamilton — 08:24 PM
Looking for any info: 1977 Ford-Philco Console Hi-Fi Turntable and Radio
Hi there! this is my first time posting. I recently picked up this Ford-Philco Console record player and radio at a yard...PittsburghToast — 07:28 PM
philco predicta
I found that where I have the 140v B+ there is 50v and the tuner receives 235v through the orange cablecgl18 — 04:14 PM
Philco 91 code 221
Chassis grounds thru rivets is another good place to look. Oh and the stator screws on the tuning cap where the leads at...Radioroslyn — 08:11 AM
Philco 91 code 221
Dirty tube pins and socket, cold solder joint, stray tiny strand of wire, clean the entire area around the oscillator tu...RodB — 08:43 PM
Philco 91 code 221
I have been restoring one of these sets and switched it on yesterday. It didn't exactly spring into life, but after a co...Philconut — 08:26 PM

[-]
Who's Online
There are currently 1290 online users. [Complete List]
» 1 Member(s) | 1289 Guest(s)
Avatar

>