Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Ready for finish
#1

Time to get the cabinets ready for the restored chassis’s.  Four Philcos, one Crosley, and one Radiola.  So much to do so many radios so little time LOL.

So, we now have 5 of the six ready to put back together.


Attached Files Image(s)
       

Philco's 
86 Low Boy     71B      42-321T
90 High Boy    52B      46-1203
95 High Boy    118B     48-214     
112X Console     60B       48-206
118X Console     84B       49-506
41-608P Console   610B   76 High Boy
41-265 Console   37-89B   370LZ
52GC                38-35B
20 Baby Grand   38-10T
70 Baby Grand   41-221CI

#2

How was the finish stripped on each of these?
#3

Klean Strip.  Just put the decals on four ready for the final two coats of lacquer tomorrow            

Philco's 
86 Low Boy     71B      42-321T
90 High Boy    52B      46-1203
95 High Boy    118B     48-214     
112X Console     60B       48-206
118X Console     84B       49-506
41-608P Console   610B   76 High Boy
41-265 Console   37-89B   370LZ
52GC                38-35B
20 Baby Grand   38-10T
70 Baby Grand   41-221CI

#4

They are all looking good. It does make a real difference when the decals are on.
   I like your choice of colors,,not too  overly done.
    
It must be nice to be able to do cabinet refinishing during the winter
  I have to wait another three months   before I can think about getting to the cabinets.
 Dan in Calgary

   Living in Calgary Alberta
#5

Thanks Dan.  I put a heater in my garage normally I would be waiting a few more months as well

Philco's 
86 Low Boy     71B      42-321T
90 High Boy    52B      46-1203
95 High Boy    118B     48-214     
112X Console     60B       48-206
118X Console     84B       49-506
41-608P Console   610B   76 High Boy
41-265 Console   37-89B   370LZ
52GC                38-35B
20 Baby Grand   38-10T
70 Baby Grand   41-221CI





Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55. I ...georgetownjohn — 07:31 PM
12' Philco
There was also this Philco! klondike98 — 07:25 PM
HiFi (Chifi) tube amp build - but my own design.
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM
Shadow Meter Bulb
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM
HiFi (Chifi) tube amp build - but my own design.
Mike, Tim; you are about to enter the twilight zone. Doo doo doo doo, doo doo doo doo This is something alright. I'm go...RodB — 06:26 PM
HiFi (Chifi) tube amp build - but my own design.
:lol: We need to start a singing radio group! I play the guitar, so maybe get a few vocals? Anyways, Mike, I did try mou...TV MAN — 05:56 PM
HiFi (Chifi) tube amp build - but my own design.
And so does a barber shop quartet. mmmmmmRodB — 03:54 PM
Shadow Meter Bulb
I did try an LED bulb in place of the original but wasn't impressed with the amount of light on the dial. Seems like it ...RodB — 03:51 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Would mounting he transformer vertically change the hum, if used without additional parts? Also, in these amps...morzh — 02:25 PM
Shadow Meter Bulb
Gary I doubt it would introduce any noise. We use similar lamps for the panel indication, 12V AC lamps: they are LEDs...morzh — 02:15 PM

[-]
Who's Online
There are currently 6150 online users. [Complete List]
» 5 Member(s) | 6145 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>