1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
How to remove glass bezel on 37-630
copiertech
Junior Member
**
Posts: 8
Threads: 3
Joined: Dec 2011
City: Fredericton State, Province, Country: New Brunswick
#1

01-02-2012, 04:15 PM
Hi: I just finished the electronic restoration of my 37-630 and I would like to clean the dust under the glass bezel. Is there an easy way to remove it or do I have to dismantle the support structure on the inside of the cabinet? Thanks for any advice, John Icon_smile
Fredericton,  N.B.  Canada
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

01-02-2012, 05:30 PM
Push the face in and give it a twist to the left.
Terry
ps back in the '80's is worked for Savin and Ricoh corp down the in Wash DC area.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
copiertech
Junior Member
**
Posts: 8
Threads: 3
Joined: Dec 2011
City: Fredericton State, Province, Country: New Brunswick
#3

01-02-2012, 08:27 PM
Hey Thanks Terry: It's always easy when you know how. I couldn't find any reference on the net to the procedure to remove the bezel. There's one now thanks to you. Yes, I'm a copiertech . I've been soldiering away at it for almost 30 years now. Don't you miss breathing that toner dust? John
Fredericton,  N.B.  Canada
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

01-02-2012, 08:53 PM
Nah don't miss it at all. When I started all the copiers I worked on where liquid tone jobs. Those blankity blank things would leak toner all over the place and where a mess to clean that's why nobody would clean them which caused them to leak more.
I have a friend still in the biz he's got about 30yrs too.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration