1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
dial lamps sockets and repair
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#1

01-05-2013, 06:32 PM
I'm fairly certain I have seen a thread or something in Chuck's forum on how to properly rebuild dial light sockets. Could be my aging brain but I can't seem to find it. Need the hints on the rubber in the socket and what to use. Mine on a 38-116 have just fallen apart. No connection to the bulb with nice power to them. No shorts yet! A little help please?

Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#2

01-05-2013, 06:38 PM
http://www.philcoradio.com/tech/lamps.htm
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#3

01-05-2013, 07:14 PM
TA, that was exactly what I was looking for thanks so much. Now if anyone out there has a parts chassis for a 38-116, I need a couple parts. See the wanted add on the forum. I can remember when I see stuff of interest but often times when I need the info I forget where it was at.
A friend in need is a pest!  Bill Slee ca 1970.
Find
Arran
Phorum Expert
*****
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#4

01-05-2013, 09:26 PM
Another trick may be to find a flat faucet washer of about the same size to use as an insulator, those are made out of a hard black rubber (likely synthetic) so they would look like they belong in there.
Regards
Arran
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 5023 online users. [Complete List]
» 1 Member(s) | 5022 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios