Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Who's in Michigan that would like a GE Colorama CHEAP?
#1

http://www.ebay.com/itm/VINTAGE-GE-AM-SW...3381964937

I'd give my 200 MHz dual trace scope for one of these....
#2

Tell you what.. if someone will give this a good home, I'll PAY for it and you can just pick it up. I just don't want to see this go to being a bar or a digital entertainment center... not at that price.
#3

If I had any plans to go near Michigan I would get it myself, I like G.E sets. With regard to good candidates to turn into something else, this Philco 16X cabinet with the plastic Hong Kong cathedral stuffed into the front would be a good candidate for that, or as a veneer donor, or for burning.

http://www.ebay.com/itm/Antique-Philco-M...RTM1303753

Regards
Arran
#4

Nice looking set! I'd buy it and I'm cheap!! But alas it's too far away.
Terry
#5

hey Micheal Dennis...this radio is just a little south of you! Actually, the set is in very southwest lower Michigan...closer to Indiana or Illinois folks. Take care all. Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#6

Brenda, is it something you cannot get to? I know a couple of collectors out that way, i can send them the link.

Paul

Tubetalk1
#7

I have no way to personally get to anything. I'm at an overseas US military installation, so my only way to get radios is via USPS/MPS. Give the link to whomever you like, I just want to see this set go to someone who will restore it rather than use it for some crazed steampunk or modernization scheme.
#8

I'm North of Detroit. These GE sets are nice, though not one of my holy grails.

Is the price on the eBay auction what you want for it. or fill mr in with the details.

Might be well to PM me, and we can talk.
#9

Not my set. I just want it to go to someone who will appreciate it, since I have no way to get it myself. These Coloramas are fairly rare, and very nice sets.
#10

Didn't sell and is relisted. I have a trashed cabinet and would buy this if it was closer.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2761 online users. [Complete List]
» 2 Member(s) | 2759 Guest(s)
AvatarAvatar

>