Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My 37-630 chassis project is completed
#1

Thanks to Ron & all here on this forum that helped me with questions here! I also send my best "regards" to whoever designed the Philco mid-Rf chassis design!! That design deserves some special credit indeed!! Special thanks goes also to JF Riders for providing me a original "readable" print that is in my in-house collection of orig service manuals. The "Philco condensers & more" book I purchased from AES several yrs ago also came in very handy!! This orig 37-630 chassis showed up via my Wife in my repair shop.Her Dads orig "heirloom-family" chassis saved by her older Bro.It was a "chassis only" project. No orig cabinet (X) orig type console. I purchased on eBay the shadowmeter-escutcheon from a canadian radio, & a nice US model 37-610 (shouldered tombstone) cab & chassis for my retrofit. Everything fits except trying to mount orig spkr over the shadowmeter assy. I can retrofit a smaller PM type new spkr in its place. This is a true "one-off" Frankenradio, but hey, "three gang condensers & 6- tubes RULE!!! Thanks to Ron for helping me identify it!... the chassis is now fully-serviced!! All new caps, all new "point-to-point" wiring, (even AC trans leads, & IF Cans connects), this is a "true 6-tube performer"!! This chassis is performing as new on all Bands. I still need to "tweak" the shadowmeter? May need somemore guidance there. The shadowmeter #44 bulb is "lit" at least!! Installed new mid-chassis rubber-grommets from special-order (Thanks Ed!!),were back on the air!!! Randal




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 96 cabinet veneer
I can't figure out what the first step is, let alone the final step. I have tried copying pictures from my hard drive a...TGLager — 01:40 PM
Philco 38-2 Low Volume
I managed to get some more time on this. Hi Mr. FixIT, The radio has been recapped. Many of the resistors were rep...dconant — 01:39 PM
Philco 38-2 Low Volume
Thanks guys for the help. I started looking at these points but I have to quit for the day. I will be looking into this ...dconant — 12:23 PM
RCA WV-98c
Check out this crazy zero pot operation. Touching it drives it crazy. Its rubber tipped. Also the 6al5 has no negative v...daveone23 — 12:08 PM
Philco 38-2 Low Volume
If you check all of that and still have a problem (my first inkling would be one of the 6F6s) then look at the 6J5 phase...RodB — 10:44 AM
RCA WV-98c
Those will probably depend on teh switch combination. Could you list some that you see, their values and what they sh...morzh — 10:26 AM
Model 96 cabinet veneer
You are probably skipping the final step. Once you select the photos you want and they get downloaded, the system assign...RodB — 09:36 AM
RCA WV-98c
At this point, there is no input, just internal voltages Which are incorrect and not sure what they should be.daveone23 — 09:15 AM
Philco 38-2 Low Volume
Hi DConat, Generally, the lower the plate voltage the less negative the grid voltage has to be. Since the plates an...MrFixr55 — 09:27 PM
RCA WV-98c
If I had it in front of me, I would triy to trace the signal on one of the non-working functions. Try to trace and high...morzh — 08:21 PM

[-]
Who's Online
There are currently 1223 online users. [Complete List]
» 1 Member(s) | 1222 Guest(s)
Avatar

>