Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 60L - Decal
#1

Hello,
I'm restoring a Philco 60 Lowboy, Canadian version.
The cabinet had already been stripped and I'm looking to reproduce the Philco decal. While I've seen that some are available commercially, from looking at other posting, there seems to be some question as to who gets them right. Since I already doing decals, I'd like to reproduce this one as well ( unless I can get a good commercial match.

So, would anyone know the correct size for this label or even, maybe a picture of an original. Ron posted some Philco label pictures on another post, I'm not sure if these would apply to my model.

Thanks for the help,
Daniel
#2

Hi Daniel

Here are a couple of the posts you mentioned.
http://philcoradio.com/phorum/showthread.php?tid=104
http://philcoradio.com/phorum/showthread.php?tid=529

The original decal used on your Model 60L was 1-1/2" long, and would have looked like this (image shown from a 645B tombstone, same decal):
[Image: http://i326.photobucket.com/albums/k420/...decal1.jpg]

Radio Daze offers the PH8 decal shown below, which is not exactly like the original.
[Image: http://i326.photobucket.com/albums/k420/...decal2.jpg]

--
Ron Ramirez
Ferdinand IN
#3

Thanks Ron for the info. BTW your article on the model 60 schematic variation is very well done and really get the confusion out. I really appreciate it.

I have one last question regarding the age of the radio. On your site I found reference to the 60L from January 1934, and on the evolution of the model 60 page, it indicates an introduction date as July 1933 but on my nameplate I find a patent date as 1930. So was this model produced in 1930 ?
Regards
Daniel
#4

No, the Model 60 had not even been thought of in 1930. The first Model 60 sets came out in July 1933, as shown on my website.

Patent numbers shown on those Philco patent labels can predate the actual manufacture of the radio by years; sometimes a patent could be several years older than the radio itself. For example, Edwin Howard Armstrong invented the superheterodyne circuit during World War I, but it did not come into general use until 1930.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need Help to ID this radio 11 tube Philco
Yes the 16B as morzh pointed out. Specifically its the January 1935 model version of the 16B. There are a couple earli...klondike98 — 11:51 PM
48-482 rear panel help
Welcome to the Phorum, keithchip! How far you take a radio on cabinet restoration is a matter of personal preference. ...GarySP — 11:28 PM
48-482 rear panel help
I've recently finished the internal restoration of a locally purchased Philco 48-482. The cabinet is in ok shape except ...keithchip — 10:28 PM
Need Help to ID this radio 11 tube Philco
Welcome to the Phorum, Ken! Lots of help here for all of your restoration questions. Take care and BE HEALTHY! - Gar...GarySP — 07:59 PM
Need Help to ID this radio 11 tube Philco
Thank you. I went to your online library and found 2 schematics. I will download and compare to components!Ken D. — 06:31 PM
Need Help to ID this radio 11 tube Philco
It is a 16B tombstone.morzh — 06:13 PM
Zenith H725
David - sorry, I reread your post and finally saw THD - now the % figures make sense. Thanks for explaining. The PSU...EdHolland — 06:06 PM
Need Help to ID this radio 11 tube Philco
Hi Everyone, New member but have been reading this for awhile for tips! Vaccum tubes were before my time so bear with ...Ken D. — 06:03 PM
My Philco 37-116 Restore
Thank you MrFixR55, I appreciate your comments very much. I do not detect much hum if any so I will be staying with the ...dconant — 05:15 PM
My Philco 37-116 Restore
Hi DConant Yes, you can replace chokes with resistors.  You do stand the risk of increased hum.  the solution is to inc...MrFixr55 — 04:23 PM

[-]
Who's Online
There are currently no members online.

>