Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Trying to restore Predicta Channel Knob...
#1

I now have a few Predicta knobs, but all 3 have the Brass/Gold worn off the channel knob. What have you guys used to get the knob to look right. I'm really only looking to paint where you would grab it. The numbers are fine.
#2

I think you mean the flat "bar" that you grip to change channels. I'm not sure what exactly Philce used on the Predicta metal parts to give them a brass look. If it's real brass plate, it's really thin. I've seen some guys have the CRT tubular arms and base commercially replated and they look awesome, but that's expensive.

I've been thinking about giving gold tinted lacquer a try. The trick is going to be getting the base metal polished and very clean. Any contamination like fingerprints is going to show or cause it to not adhere well.

http://www.votawtool.com/nikolas-2105-sp...-tint.html

[Image: https://farm4.staticflickr.com/3696/1260...cb07_c.jpg]
#3

Bob;
 If you find out who makes this gold tinted lacquer I would like to know, I have a foil dial or two that used something similar and the gold came off at some point,it is obviously like a tinted lacquer or shellac, not like gold paint as it has no flakes in it. I thought about using tinted glass paint, the kind you use to make faux stained glass, but I haven't been able to find any in a yellow colour.
Regards
Arran
#4

Nikolas.  Here's a link:  http://www.votawtool.com/nikolas-2105-sp...-tint.html




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 3982 online users. [Complete List]
» 1 Member(s) | 3981 Guest(s)
Avatar

>