Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Story about Philco cabinet manufacturing
#1

I work with the author of this story. The stories are straight from the owner of the factory.

http://www.ydr.com/history/ci_24483618/j...y-was-more
#2

Thanks for sharing that link. It would be great to see some pics of the radio cabinet "assembly line".

Craig R.
#3

What a wonderful post. So much nice history there.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#4

Quote:It would be great to see some pics of the radio cabinet "assembly line".

Ask and ye shall receive.

[Image: http://i191.photobucket.com/albums/z309/...cab02s.jpg]

[Image: http://i191.photobucket.com/albums/z309/...dlion4.jpg]

Highboy?
#5

Ask and yee shall receive! That is so coooool! Thanks for that historic pic.

Craig R.
#6

Philco did have it's own cabinet plant in Philadelphia though, but they did contract out when they could not meet production by themselves. Atwater Kent relied on Pooley and Red Lion to make all of their cabinets, they had large amounts of sheet metal stamping equipment but no cabinet shop.
Regards
Arran
#7

That was interesting to read. My 87 lowboy cabinet has 'Philco Furniture, Plant 2' stamped into the wood on the back, so it seems I definitely have one of the Red Lion produced cabinets. One of the two Radiola 66 consoles I owned had a Red Lion built cabinet, but I don't know if it was the one I kept or the one I traded to a friend.

No matter where you go, there you are.
#8

Great information! Thank you for posting this.

Gene
#9

Thank you for this post. It would be good to see pictures of "from raw to ready."
#10

Thank you for posting this information. Back the a LOT of things were make in N.Y. state or needless to say in the good old U.S.A.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM

[-]
Who's Online
There are currently no members online.

>