Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Newbie attempting first restoration - Model: 38-15T
#1

Hi everyone, got a newcomer here with absolutely no prior electronics training or experience. This past Saturday I picked up a couple beautiful Philco radios; the 38-15T mentioned in the subject field and a late model 84B. The 84B appears to be in remarkable cosmetic condition so I'm leaving that one alone (for now). The 38-15T looks like someone started to work on it but gave up and just kind of reassembled it quickly. Some of the things I'm hoping to find out are:

  1. The three screws that fasten the "electronics chassis" (wrong term) to the cabinet are missing. Can anyone tell me the correct replacement screw and size?
  2. I've seen pictures on-line of the interior of this radio when viewed from behind. In those pictures one of the tubes appears to have a metal "heat shield" (wrong term) around three sides of it. Mine is missing. What is that thing I'm calling a heat shield and do I need to get another one?
  3. I'm considering ordering a replacement grill cloth from grillecloth.com and have selected their pattern #14 - Philco ribbed cotton as the closest to authentic. Is that a good choice for my radio?
  4. Lastly, like I mentioned, I have no experience restoring radios. Can anyone suggest other friendly resources on-line where I might find patient help if I need it (because I'm going to need it!)?
Thanks in advance for any help anyone may be willing to offer.
#2

Hi, and I apologize for missing your post until now. Congratulations on your acquisitions.

I do not know the correct size screw you need to replace the chassis hold-down screws, sorry. They will be small sheet metal screws, about 1-1/2 to 2 inches long.

What you are calling a heat shield is actually called a tube shield, and will be necessary for proper operation of your 38-15. Without it, the set may oscillate (squeal).

Pattern #14 is perfect for your 38-15.

You can find all the help you need right here at the Philco Phorum. If you don't get an answer right away, feel free to yell louder. Icon_lol

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 4097 online users. [Complete List]
» 1 Member(s) | 4096 Guest(s)
Avatar

>