Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

BIG ZENITH 39A FINALLY FINISHED
#1

    This zenith gave me goose bumps after I completed putting back together because I am so proud of all the hard work that I have put into this and the results are stunning. It plays very nice , it is a show piece.


Attached Files Image(s)
                   
#2

Here are a few more pictures of the zenith.


Attached Files Image(s)
                   
#3

beautifully done  fred  like it with doors open Icon_clap Icon_clap Icon_thumbup
what is lever under speaker grill ?
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#4

Gee Wizz Fred you always seem to amaze us! All I can say is WOW. That set came out beautiful. Great job I simply love it!  Icon_clap  
#5

Very nice Fred!
Icon_clap Icon_clap Icon_clap
#6

It is beautiful. Icon_thumbup You do good work.

--
Ron Ramirez
Ferdinand IN
#7

(03-20-2015, 03:00 AM)sam Wrote:  beautifully done  fred  like it with doors open Icon_clap Icon_clap Icon_thumbup
what is lever under speaker grill ?
sam

 The lever will rotate the large loop antenna that's on the inside of cabinet, you can see that antenna in one of the pictures of the back, its in the left coner.
#8

Looks great, could be a centerpiece.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#9

Fred, you do just terrific work. Lovely radio.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#10

With the Philco on top. as it should be, the Zenith is stellar.

Paul

Tubetalk1
#11

Excellent! One of the best restorations I've seen yet. Hats off to you, Fred.

Slave to an RCA Victor CTC-25
#12

   I can see that this one took a lot of work.. Hats off to  you and your ability to make it look  the way it does now.
       It  looks very good.
#13

Wow, it's beautiful!

Steve

M R Radios   C M Tubes




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently no members online.

>