Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco BOL 41-608 Turntable--HELP
#1

I'm reluctenly restoring a Philco BOL 41-608 for a customer. Having got the radio going, I am working on getting the turntable running. It looks like there is flex joint that's supposed to couple the motor to the platter. The flex joint is dried out and both halves have seperated and cracked. Have I read this right as far as how it works, AND, is there any way to fix or restore this flex joint?
#2

Hi Brian,

I restored a 41-608 about a year ago. I don't recall a flex joint to couple the motor to the platter. IIRC, the motor spindle drives two idler wheels that in turn drive the platter. I can look at the service manual on it when I get home.

Sean
WØKPX
#3

Thanks Sean, hope you can firgure it out. This one does have the record cutter head. What I have right now is 2 seperate pieces...one slips on to the motor shaft, the other slips on the platter shaft. Each piece has a metal center, with a keyway to slip on the respective shaft, and a circular rubber piece riveted each. It looks like the 2 rubber pieces were riveted together at one time. Again, this is what I found...Hopefully you can dig in and check the schematic. It is an early model, with Oct. '40 inspection date...Code 122.....hope this helps...Brian
#4

Hi Brian,

Here are a couple photos I took when I restored the phono. Does this look like what you have?

Phono Top
Phono Bottom

Sean
WØKPX
#5

In looking through the Philco service info there was a rim drive version of the phono (which is what I had) and a gear driven version. You probably have the gear driven version. Is what you are asking about part number 35-2220 shown on this page?

Sean
WØKPX
#6

Good job Sean.....Yes, I have the gear driven version...part # 35-2220 is the one that I have to fix. I went around to some hardware stores today and located a couple of 'rubber' washers that sould be used if cut down. I would have to fasten them to the metal part by some means, they were originally riveted to the metal part, and to each other, to form the coupling. Would appreciate any ideas you may have to recreate this part........




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM

[-]
Who's Online
There are currently no members online.

>