Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-660 Alignment Issue
#1

Well I've rewound the OT and it works fine. Began the alignment and all was going fine until the last SW tuning range 2 (2.3-7.4 mc). The first part of this stage you peak at 7 mc by adjusting the oscillator (30B)(no problem) and then you are to go to 2.35mc (closing the tuning cap plates) and peak there (30C) where I don't hear the sig gen signal.

If I set the sig gen to 6 mc the radio dial has to be set to about 6.65 mc to hear the tone (this is after peaking at 7 mc). To me it seems like it is short on capacitance. I note that across 30C (the 2.5 mc osc trim) there is what appears to be a large mica. According to the schematic this is 30x and is a 1150 uufd (I didn't change this one). The parts list does not say it is mica whereas it does state other small ones as mica. I am wondering if this cap might not be mica and could be causing my problem? Looking to you experts for help and suggestions.

http://www.nostalgiaair.org/PagesByModel...013220.pdf
#2

Hello, Marv: The best way to align is to connect a volt meter to the voice coil leads of your speaker and use min sig gen amplitude when adjusting your set.

This prevents your AVC circuit from interfering with your alignment.
#3

If I had to guess (and I do) Icon_wtf you are on the wrong peak. ie if the LO is to be at 6.53MHz when you tune 7Mhz, you have it peaked at 7.47 Mhz on the LO

turn the signal generator level down, and try to find a peak at 7MHz with the trimmer turned in tighter.

I would also assume the 1150 pF cap would be paper, you could try putting 2 .0022uF caps in series (1100pF) and see if the situation improves.

John
Las Vegas, NV USA
#4

Still have problem on range 2. Changed 1150pfd cap, no difference. Close inspection of coils noted that one lead of RF range 2 primary broke off wafer switch. (Probably happend when replacing caps deep within). Soldered lead back on to D3, still cannot align this range correctly.

Before I remove the RF section from chassis again to check this coil closer can someone please confirm that when the radio range lever is in range 2 I should read 12 ohms of the primary between D3 and D6 of the wafer. I read open. Getting to these coils is nearly impossible.

marv




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently no members online.

>