I must have a soft spot for Philcos...
Posts: 193
...when I paid $32 for this 37-60. That's pink paint and I have no plans to restore that photo-finish. I'm going to reveneer the front with something interesting like curly maple. I'll take my scolding later.
[Image: http://i191.photobucket.com/albums/z309/...ckudmx.jpg ]
[Image: http://i191.photobucket.com/albums/z309/...5ab4rn.jpg ]
Posts: 98
Well, we all like a challenge now and then! Sometimes you just feel sorry for one and make it your mission to save it from the scrap heap. Go for it!
Posts: 4,107
You will take your scolding now!
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 193
Quote: It's not that hard....
I hear you....barely....
.......I'll bring it to Kutztown and you'll be begging me to sell it to you
.
Posts: 4,107
Not unless the photofinish is restored.. that is hard
Me
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 1,824
I'm in the process of restoring a 37-61, which uses the same cabinet as yours. I have bought the Re-Faux Pro decals for restoring the photofinish. I have written about it in the cabinet restoration section. I'll be applying the decals come spring, it is too cold in my house to do finishing work right now. If you wait until Spring, you can see how mine turns out, and decide what you want to do then. Believe me, the decals are a lot easier than trying to re-veneer the front. I already did it once, but the decals were off. I sent Tony my own cabinet so he could correct them perfectly, so hopefully they will be right now. The curved trim lines on the curved part of the speaker grill, and the 3 center light color trim stripes were off before, now they should be right.
Posts: 83
Do it right! You'll regret it later. My 37-665B will be a challenge but well worth the effort.
Posts: 1,824
I agree, It really would be worth waiting and doing it up right, actually easier too.
(This post was last modified: 02-15-2016, 12:03 AM by
mikethedruid .
Edit Reason: mistakes
)
Posts: 765
Posts: 4,107
I used paper on mine.
I printed high res photos of the veneers and glued them on. Came out pretty D**n nice.... I want to try my hand at had restoring it with paints but my hands are not so hot these days...
Anything is Better than this...
Attached Files
Image(s)
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 13,776
What is that, a radio or a guitar body?
Posts: 4,107
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 4,682
(02-16-2016, 10:14 AM) Ron Ramirez Wrote:
Old Foggy on fleabay must have got his hands on that thing.
Users browsing this thread: 1 Guest(s)
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red.
Red is Bad.
Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.)
When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil.
It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one.
If you buy a Hammond 125 output tr...morzh — 08:15 AM
Who's Online
There are currently 5425 online users. [Complete List ]» 1 Member(s) | 5424 Guest(s)
.......I'll bring it to Kutztown and you'll be begging me to sell it to you 
.
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
