Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Dial Scale Removal
#1

I've a model 610, just 610 that's going to need the dial scale replaced. I know there are repros out and that's great, but how do you remove those scales off of their mountings? Can someone direct me to an illustration or just let me know how it's done on this forum?

This set was mentioned earlier on in the forum. Wow, what a player. Just jumpered in a few 10mfd's to get rid of the LOUD HUM to hear if it's going to be a player or not. Sounds real good. Back to the soldering tool to do it right. Thanks all for your help.

GB

73 de,

Gary/N9VU
#2

That 1 1/2 inch perforated disc in the center of the dial- put the tips of your needle nosed pliers in the holes and turn counter-clockwise just a bit. The disc will fall off; the dial simply pulls off the two pins.

In getting a replacement I recommend Mark Oppat at Antique Audio (moppat@comcast.net ); his dials are nearest to the original in color although somewhat darker. The RockSea dials are VERY light in color and look odd in my opinion.

Pete AI2V
#3

AI2V Wrote:That 1 1/2 inch perforated disc in the center of the dial- put the tips of your needle nosed pliers in the holes and turn counter-clockwise just a bit. The disc will fall off; the dial simply pulls off the two pins.

In getting a replacement I recommend Mark Oppat at Antique Audio (moppat@comcast.net ); his dials are nearest to the original in color although somewhat darker. The RockSea dials are VERY light in color and look odd in my opinion.

Hey, thanks for the info. I didn't realize it was that simple. I'll give it a
try. Thanks for the advice on dial covers as well. I've only bought one in my radio career from RocksSea and you're correct, looks a bit brighter than usual, but I do like it. Thanks again for the helpful advice. GB.

73 de,

Gary/N9VU




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently no members online.

>