|
Starting on the Philco 610 from 1936
10-14-2019, 10:20 PM
Jake, when you get to replacing the electrolytic condensers, go by the Philco schematic for values. Don't follow some later on replacement values. They may have been done during World War 2 and be whatever the repair guy could get his hands on. I ran into a similar problem with all three electrolytics on my T8-18 I just did. As I mentioned before, it is OK, actually good, to go up a little in MFD, but never lower.
« Next Oldest | Next Newest »
Messages In This Thread
Starting on the Philco 610 from 1936 - by Jake Blake - 10-11-2019, 03:04 PM
RE: Starting on the Philco 610 from 1936 - by klondike98 - 10-11-2019, 03:43 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-11-2019, 04:35 PM
RE: Starting on the Philco 610 from 1936 - by Simon Wa3uay - 10-11-2019, 07:44 PM
RE: Starting on the Philco 610 from 1936 - by Radioroslyn - 10-11-2019, 10:03 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 07:32 AM
RE: Starting on the Philco 610 from 1936 - by klondike98 - 10-12-2019, 08:13 AM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 09:35 AM
RE: Starting on the Philco 610 from 1936 - by Radioroslyn - 10-12-2019, 01:25 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 01:32 PM
RE: Starting on the Philco 610 from 1936 - by Chas - 10-12-2019, 01:48 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 02:02 PM
RE: Starting on the Philco 610 from 1936 - by Steve Davis - 10-12-2019, 06:12 PM
RE: Starting on the Philco 610 from 1936 - by Simon Wa3uay - 10-12-2019, 06:16 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 06:16 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-12-2019, 09:22 PM
RE: Starting on the Philco 610 from 1936 - by mikethedruid - 10-13-2019, 01:41 AM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-13-2019, 07:45 AM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-13-2019, 08:07 AM
RE: Starting on the Philco 610 from 1936 - by mikethedruid - 10-13-2019, 02:30 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-13-2019, 03:40 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-14-2019, 07:46 PM
RE: Starting on the Philco 610 from 1936 - by klondike98 - 10-14-2019, 08:15 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-14-2019, 08:49 PM
RE: Starting on the Philco 610 from 1936 - by mikethedruid - 10-14-2019, 10:20 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-15-2019, 07:50 AM
RE: Starting on the Philco 610 from 1936 - by Ron Ramirez - 10-15-2019, 11:00 AM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-15-2019, 01:43 PM
RE: Starting on the Philco 610 from 1936 - by Jake Blake - 10-15-2019, 10:47 PM
Users browsing this thread: 2 Guest(s) |
