Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Got a 39-6 today
#21

Hey Jake, I had to redo the dial cord on my 39-6 also. The spring was on the right side of the screw and the loop for the other end was on the left. Make sure when you install the dial cord there is tension on the cord; it has to be somewhat tight, but NOT so tight that it causes the tuner frame to move . If the cord is too loose, it will slip. It took me several tries before I got it just right and now it tunes both directions perfectly. Take your time.


Messages In This Thread
Got a 39-6 today - by morzh - 09-13-2014, 02:20 PM
RE: Got a 39-6 today - by morzh - 09-13-2014, 02:25 PM
RE: Got a 39-6 today - by sam - 09-13-2014, 06:59 PM
RE: Got a 39-6 today - by Ron Ramirez - 09-13-2014, 07:38 PM
RE: Got a 39-6 today - by morzh - 09-13-2014, 07:43 PM
RE: Got a 39-6 today - by Ron Ramirez - 09-13-2014, 07:53 PM
RE: Got a 39-6 today - by morzh - 09-13-2014, 08:07 PM
RE: Got a 39-6 today - by BenWA - 09-13-2014, 11:21 PM
RE: Got a 39-6 today - by morzh - 09-14-2014, 09:07 AM
RE: Got a 39-6 today - by klondike98 - 09-14-2014, 11:10 AM
RE: Got a 39-6 today - by morzh - 09-14-2014, 04:18 PM
RE: Got a 39-6 today - by PhilcoJohn - 09-14-2014, 05:55 PM
RE: Got a 39-6 today - by morzh - 09-14-2014, 06:17 PM
RE: Got a 39-6 today - by Arran - 09-16-2014, 12:30 AM
RE: Got a 39-6 today - by Jake Blake - 01-01-2020, 09:27 PM
RE: Got a 39-6 today - by Tubeglow20 - 01-01-2020, 11:10 PM
RE: Got a 39-6 today - by rfeenstra - 01-01-2020, 11:46 PM
RE: Got a 39-6 today - by morzh - 01-02-2020, 10:01 AM
RE: Got a 39-6 today - by Radioroslyn - 01-02-2020, 10:42 AM
RE: Got a 39-6 today - by Jake Blake - 01-02-2020, 10:21 PM
RE: Got a 39-6 today - by Tubeglow20 - 01-03-2020, 12:45 AM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 08:26 AM
RE: Got a 39-6 today - by Radioroslyn - 01-03-2020, 11:33 AM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 12:30 PM
RE: Got a 39-6 today - by Phlogiston - 01-03-2020, 01:04 PM
RE: Got a 39-6 today - by Radioroslyn - 01-03-2020, 01:05 PM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 01:53 PM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 02:01 PM
RE: Got a 39-6 today - by klondike98 - 01-03-2020, 04:12 PM
RE: Got a 39-6 today - by Phlogiston - 01-03-2020, 06:31 PM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 07:15 PM
RE: Got a 39-6 today - by Tubeglow20 - 01-03-2020, 09:17 PM
RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 11:14 PM
RE: Got a 39-6 today - by Art Hoch - 01-07-2020, 10:26 AM
RE: Got a 39-6 today - by Jake Blake - 01-07-2020, 10:52 AM
RE: Got a 39-6 today - by Ron Ramirez - 01-07-2020, 08:33 PM
RE: Got a 39-6 today - by Jake Blake - 01-08-2020, 06:48 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 3941 online users. [Complete List]
» 1 Member(s) | 3940 Guest(s)
Avatar

>