Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-123
#16

Finally got thru the radio again and think I have the wiring right. Powered it up and got nothing, no sound or noise of any type. Checked the B+voltage on the tubes and they were in spec. Checked the resistance of the osc coil and it was fine. Tried the 2nd radio test and no squeal anywhere on the dial. I dont know what to do next. Seems like this critter has more aches and pains than I do. Any ideas would be greatly appreciated.
George


Messages In This Thread
Philco 42-123 - by texan george - 10-01-2021, 01:15 PM
RE: Philco 42-123 - by admin - 10-01-2021, 02:12 PM
RE: Philco 42-123 - by morzh - 10-01-2021, 05:15 PM
RE: Philco 42-123 - by Radioroslyn - 10-01-2021, 06:45 PM
RE: Philco 42-123 - by morzh - 10-01-2021, 08:57 PM
RE: Philco 42-123 - by Radioroslyn - 10-02-2021, 05:19 AM
RE: Philco 42-123 - by MrFixr55 - 10-02-2021, 08:17 AM
RE: Philco 42-123 - by texan george - 10-02-2021, 02:55 PM
RE: Philco 42-123 - by texan george - 10-04-2021, 08:44 PM
RE: Philco 42-123 - by Radioroslyn - 10-04-2021, 10:30 PM
RE: Philco 42-123 - by texan george - 10-05-2021, 10:36 AM
RE: Philco 42-123 - by texan george - 10-10-2021, 08:43 AM
RE: Philco 42-123 - by Radioroslyn - 10-10-2021, 11:34 AM
RE: Philco 42-123 - by radiorich - 10-10-2021, 11:51 AM
RE: Philco 42-123 - by texan george - 10-10-2021, 01:28 PM
RE: Philco 42-123 - by texan george - 10-13-2021, 12:17 PM
RE: Philco 42-123 - by mikethedruid - 10-13-2021, 01:18 PM
RE: Philco 42-123 - by texan george - 10-13-2021, 02:35 PM
RE: Philco 42-123 - by RodB - 10-13-2021, 03:20 PM
RE: Philco 42-123 - by texan george - 10-15-2021, 12:37 PM
RE: Philco 42-123 - by Radioroslyn - 10-15-2021, 02:41 PM
RE: Philco 42-123 - by texan george - 10-16-2021, 03:22 PM
RE: Philco 42-123 - by morzh - 10-16-2021, 07:38 PM
RE: Philco 42-123 - by texan george - 10-24-2021, 04:10 PM
RE: Philco 42-123 - by MrFixr55 - 10-24-2021, 08:44 PM
RE: Philco 42-123 - by texan george - 10-26-2021, 12:50 PM



Users browsing this thread: 1 Guest(s)