|
Philco 41-280
01-03-2012, 07:52 PM
Nah that cap is not going to do it. Triple check your wiring of the caps that you replaced and any bad rubber wire. Make sure you've got plate and screen grid voltage on the 41's
Terry When my pals were reading comic books I was down in the basement in my dad's workshop. Perusing his Sam's Photofoacts Vol 1-50 admiring the old set and trying to figure out what all those squiggly meant. Circa 1966 Now I think I've got! Terry
« Next Oldest | Next Newest »
Messages In This Thread
Philco 41-280 - by OldJack1969 - 01-03-2012, 06:08 PM
Re: Philco 41-280 - by 7estatdef - 01-03-2012, 07:52 PM
Re: Philco 41-280 - by OldJack1969 - 01-04-2012, 05:55 PM
Re: Philco 41-280 - by 7estatdef - 01-04-2012, 10:49 PM
Re: Philco 41-280 - by OldJack1969 - 01-04-2012, 11:00 PM
Re: Philco 41-280 - by OldJack1969 - 01-05-2012, 12:09 AM
Re: Philco 41-280 - by 7estatdef - 01-05-2012, 06:28 PM
Re: Philco 41-280 - by OldJack1969 - 01-05-2012, 07:25 PM
Re: Philco 41-280 - by 7estatdef - 01-05-2012, 10:28 PM
Re: Philco 41-280 - by OldJack1969 - 01-05-2012, 11:05 PM
Re: Philco 41-280 - by 7estatdef - 01-06-2012, 07:47 AM
Re: Philco 41-280 - by OldJack1969 - 01-06-2012, 12:35 PM
Re: Philco 41-280 - by 7estatdef - 01-06-2012, 04:42 PM
Re: Philco 41-280 - by OldJack1969 - 01-07-2012, 11:43 PM
Re: Philco 41-280 - by Phlogiston - 01-07-2012, 11:56 PM
Re: Philco 41-280 - by OldJack1969 - 01-08-2012, 12:10 AM
Re: Philco 41-280 - by 7estatdef - 01-08-2012, 02:30 PM
Re: Philco 41-280 - by OldJack1969 - 01-08-2012, 02:45 PM
Re: Philco 41-280 - by gary rabbitt - 01-23-2012, 07:38 PM
Re: Philco 41-280 - by OldJack1969 - 01-23-2012, 08:29 PM
Re: Philco 41-280 - by gary rabbitt - 01-24-2012, 03:58 PM
Re: Philco 41-280 - by OldJack1969 - 01-24-2012, 04:10 PM
Re: Philco 41-280 - by 7estatdef - 01-24-2012, 05:17 PM
Re: Philco 41-280 - by OldJack1969 - 01-24-2012, 05:50 PM
Re: Philco 41-280 - by 7estatdef - 01-24-2012, 05:56 PM
Re: Philco 41-280 - by OldJack1969 - 01-24-2012, 06:15 PM
Users browsing this thread: 3 Guest(s) |
