1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 90 Stuck At One Volume Level
morzh
Odobenus rosmarus
*****
Posts: 15,691
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
#4

04-12-2012, 09:19 PM
Is your volume control GND terminal connected to the Chassis?

Use Ohm-meter, make sure it is connected, not to the rivet, but to the chassis.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Model 90 Stuck At One Volume Level - by Pepperoni - 04-12-2012, 03:54 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-12-2012, 09:19 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 02:44 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 02:52 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 06:16 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-14-2012, 08:51 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-15-2012, 12:04 PM
RE: Model 90 Stuck At One Volume Level - by morzh - 04-15-2012, 01:26 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM

[-]
Who's Online
There are currently 5354 online users. [Complete List]
» 1 Member(s) | 5353 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration