Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 57 compensator values?
#16

Have you aligned the RF and IF stages with a signal generator? These sets to work properly need a good alignment especially after moving the wiring around while fooling with the trimmer caps. I trust that you have replaced the paper caps and checked the resistors to be intolerance.
Terry


Messages In This Thread
Model 57 compensator values? - by earlyradios - 04-07-2015, 09:34 AM
RE: Model 57 compensator values? - by klondike98 - 04-07-2015, 09:46 AM
RE: Model 57 compensator values? - by Radioroslyn - 04-07-2015, 07:47 PM
RE: Model 57 compensator values? - by morzh - 04-07-2015, 08:12 PM
RE: Model 57 compensator values? - by Radioroslyn - 04-07-2015, 09:00 PM
RE: Model 57 compensator values? - by morzh - 04-07-2015, 09:16 PM
RE: Model 57 compensator values? - by Radioroslyn - 04-07-2015, 09:37 PM
RE: Model 57 compensator values? - by earlyradios - 04-07-2015, 11:54 PM
RE: Model 57 compensator values? - by Ron Ramirez - 04-08-2015, 06:41 AM
RE: Model 57 compensator values? - by earlyradios - 04-08-2015, 09:13 AM
RE: Model 57 compensator values? - by earlyradios - 04-12-2015, 04:47 PM
RE: Model 57 compensator values? - by klondike98 - 04-12-2015, 05:22 PM
RE: Model 57 compensator values? - by Ron Ramirez - 04-12-2015, 05:34 PM
RE: Model 57 compensator values? - by earlyradios - 04-12-2015, 11:04 PM
RE: Model 57 compensator values? - by earlyradios - 04-12-2015, 11:05 PM
RE: Model 57 compensator values? - by Radioroslyn - 04-13-2015, 04:48 AM
RE: Model 57 compensator values? - by earlyradios - 04-13-2015, 09:32 AM
RE: Model 57 compensator values? - by Radioroslyn - 04-13-2015, 06:44 PM
RE: Model 57 compensator values? - by earlyradios - 04-14-2015, 09:30 AM
RE: Model 57 compensator values? - by earlyradios - 04-20-2015, 09:30 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 3977 online users. [Complete List]
» 1 Member(s) | 3976 Guest(s)
Avatar

>