Posts: 111
Threads: 2
Joined: Nov 2016
City: marystown nl canada
and both pulling tubes and my signal tracer put me in that area for the problem but is it still possible to have the battery hooked up wrong or a cap somewhere else because if I was sure the other connection were correct then I would be at a stand still unless it has a exposed wire somewhere and would that do it
Posts: 111
Threads: 2
Joined: Nov 2016
City: marystown nl canada
any ideas on what I could try next thanks
Posts: 15,691
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
Short of sending it to someone who would agree to look at it, I am short of ideas.
Try changing tubes.
Moving wires.
Introducing shields.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 111
Threads: 2
Joined: Nov 2016
City: marystown nl canada
the problem I have is I only know of two people in nl that repair radios and they are retired and only take the odd job so thanks I will try some of those things but my problem is it did not do this before I recapped the radio
Posts: 15,691
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
Recheck all caps. Especially the electrolytics. There are three.
Motorboating often IS the result of capacitors' screwup.
Especially decoupling ones. Think back to how it was. See if there are shorts.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 11-28-2016, 08:29 PM by morzh.)
Posts: 111
Threads: 2
Joined: Nov 2016
City: marystown nl canada
There are only three electrolytics and two was in a can and they were marked white for 10 mfd red for 20 mfd and black for negative and they other 25 mfd positive goes to pin 8 of tube 6f6 and the other to ground.But can you slice the two grounds from both 10 and 20 mfd and then go to ground
Posts: 111
Threads: 2
Joined: Nov 2016
City: marystown nl canada
rechecked the caps and all seem to be fine
Posts: 15,691
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
I don't know what to tell you.
According to you, the phenomenon started after you recapped the radio.
Retrace the steps, if you took any photos- look at those, and (this is where reading the sch is needed) start comparing whatever it is you did (soldering, wiring, recapping, recarbing) to the sch.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 111
Threads: 2
Joined: Nov 2016
City: marystown nl canada
the only I did other than recap was added a couple of new pieces of wire to the ends of a couple of resistors
Posts: 1,107
Threads: 88
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
I got to seriously looking under the chassis of this thing... someone who knows NOTHING about electronics has worked on it. There are resistors that have been put in parallel that should be in series (voltage divider), missing resistors, a large cap to ground from the grid of the output tube... lots of fun carp. This is going to be a lot of work.
Posts: 15,691
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
The caps...CapXon....never heard of these.
Seriously. You need to get someone with experience to look at it.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 111
Threads: 2
Joined: Nov 2016
City: marystown nl canada
(12-08-2016, 07:28 PM)BrendaAnnD Wrote: I got to seriously looking under the chassis of this thing... someone who knows NOTHING about electronics has worked on it. There are resistors that have been put in parallel that should be in series (voltage divider), missing resistors, a large cap to ground from the grid of the output tube... lots of fun carp. This is going to be a lot of work.
not sure what is wrong with the radio but I was told the radio worked before it was stored for 15 years
Posts: 111
Threads: 2
Joined: Nov 2016
City: marystown nl canada
(12-08-2016, 07:48 PM)morzh Wrote: The caps...CapXon....never heard of these.
Seriously. You need to get someone with experience to look at it.
these caps came from just radios and there is no one in newfoundland to get to look at it I tried
Posts: 15,691
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
Gee dude....I dunno if it is worth it for you and how urgent this resto is (who are you gonna show it off to, polar beare?) - but if you want to pay the shipping to and from NJ plus parts (only if required) I could, (considering I have my own plate full plus I owe our own Kirk looking at a couple of his chassis) at a reasonable schedule look at it for you.
Any open coils etc....I am not crazy about those. But I could run the comparative plus take care of some especially hideous rework places.
I will use your box to ship it back so packing has to be reliable.
Consider that the shipping costs if packed properly could be more than the radio itself.
Mike.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 12-08-2016, 08:50 PM by morzh.)
Posts: 111
Threads: 2
Joined: Nov 2016
City: marystown nl canada
thanks so much for the offer but shipping would be the killer . it would be better to buy a working chassis and have it shipped
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Jackson 715 not working
|
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM |
Jackson 715 not working
|
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM |
HiFi (Chifi) tube amp build - but my own design.
|
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM |
Jackson 715 not working
|
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM |
Restoring Philco 37-604C
|
Yep. F5 is green, D5 is Red.
Red is Bad.
Green is Clean.morzh — 01:30 PM |
Jackson 715 not working
|
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM |
Restoring Philco 37-604C
|
(Insert Homer Simpson "DOPF" Here.)
When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM |
Philco 91 Speaker Replacement
|
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil.
It wo...morzh — 08:44 AM |
Philco 91 Speaker Replacement
|
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM |
Philco 91 Speaker Replacement
|
As Rod said, it is OK to use a fitting speaker, and then look for an original one.
If you buy a Hammond 125 output tr...morzh — 08:15 AM |
Who's Online
|
There are currently 3872 online users. [Complete List] » 1 Member(s) | 3871 Guest(s)
|
|
|
|